Jump to content
SAU Community

Recommended Posts

I just got an Autometer boost gauge, the white one and was wondering if anyone knows where it can be mounted, rather than the pillar. Just want to put it somewhere where i can see it whilst driving, but thieves can't when looking into my car?

Also, they are pretty easy to install right? Anyone done their own before?

Cheers

Kris

Link to comment
https://www.sau.com.au/forums/topic/25448-autometer-boost-gauge/
Share on other sites

dont bother with the din slot - you'll never be able to see the needle over the lip of the gauge.

been there.

be like me - tough and dangerous - and zip tie the baarstard to the vent - it's cheap and it's functional...and you get extra street cred for being tough and povvo like me.

Originally posted by zanda

dont bother with the din slot - you'll never be able to see the needle over the lip of the gauge.

been there.

be like me - tough and dangerous - and zip tie the baarstard to the vent - it's cheap and it's functional...and you get extra street cred for being tough and povvo like me.

Zanda,

If that is the case, you car must have lots of street cred hehehe isnt held together by zip ties.

Sits back waiting to be spanked :shake:

hahaha sounds familiar and just as dodgy Paul!!! :)

double sided tape probably wont work, because it doesnt stick to the dash and stuff very well (unless its on a flat bit).

Just go a DECENT pillar mount and do it properly the first time. It looks the best IMHO and is the most conveniant method

Trust me...... i know these things (isn't that rite paul :mad: )

yeh it will work out the easiest

I have a cheap imitation style pillar mount, which does the job. it looks kinda shithouse though. I bought it from Motoquipe (not a bad little semi-rice shop in floreat) for like $20

Places like supercheap etc sell universal pillar mounts, but for a proper moulded one for a 33, your looking at $$$.

The skyline i almost bought had a boost guage mounted just behind the steering wheel too. That looked pretty good too. I've got some pics if you want them (email i guess).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...