Jump to content
SAU Community

Recommended Posts

just taken these off my car after having them on for a few years now..

all 4 are in good condition no big scratches or gutter rash but are in need of a good clean..

2 tyres are good, 2 poor..

comes with the 20x hex key wheel nuts as i dont need them any more

as topic says they came off a r33 gtst and looking for pickup only.. located in Mentone/Parkdale area ( S.E melb)

LF $600ono

post-1162-1233385833_thumb.jpgpost-1162-1233385965_thumb.jpg

post-1162-1233386008_thumb.jpgpost-1162-1233386054_thumb.jpg

post-1162-1233386106_thumb.jpgpost-1162-1233386173_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/254978-fs-vic-18-white-5spoke-rims-33gtst/
Share on other sites

Any other pics of these rims on your car dude?

Im looking for rims that I can have powdercoated black, and these might fit the bill nicely.

If they are in decent condition and will not rub on my r33 or cause any problems, I might be interested in taking them for $500!

they're in good condition.. there's no big scratches or dents but as i said they need a good clean.. there's some brake dust looking stains on them

i had a look for the offset but i cant see it stamped or written anywhere.. they were on my 33gtst and there was no rubbing and they clear the brakes easily.. no need for spacers or anything..

post-1162-1233752267_thumb.jpg post-1162-1233752316_thumb.jpg post-1162-1233752359_thumb.jpg

these last 3 pix were taken last week a few days before i put the stockies back on.. rims were dirty and pix were taken because i just picked up the car from getting sprayed

post-1162-1233752443_thumb.jpg post-1162-1233752443_thumb.jpg post-1162-1233752534_thumb.jpg

post-1162-1233752404_thumb.jpg

Edited by SKYL9
the offset about +35? interested in trade for stockies with new rubber n cash ur way?

sorry iv just had some stockies painted and slapped on some re55s.. thats why these aren't on my car anymore

what % tread would the tires be???

the 2 that were on the front still look good and have only about a years worth of weekend driving missing from them

the 2 that were on the back are good on the outside but chopped up bad on the inside and wont pass a rw.. there's no belts or anything crazy coming through but the insides are nearly slicks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...