Jump to content
SAU Community

Recommended Posts

quick question my brother has a broken drivers side mirror glass for sometime now and wants to get it fixed

i went to a wrecker today and got told that u need to change the whole mirror

i dont think thats rite as u can change the 32 ones

is this right??

Link to comment
https://www.sau.com.au/forums/topic/255540-changing-34-mirror-glass/
Share on other sites

When the wrecker said you need to change the whole mirror, did they mean just the piece of glass/mirror or the whole side rear view mirror casing unit including the glass?

I think you can just change the piece of glass. Get a flat head screw driver and hinge out the glass to see if it will pop out... Take it easy as you don't want to dent the plastic casing around the mirror.

Also be aware of the electronic mechanisim that allows you to adjust the angle of the mirror, you don't wanna damage it.

Yeah..?

i changed mine yesterday very simple you dont need to take off anything

as mentined above get a wide flat head screwdriver and place it underneath the mirror, or adjust the angle of the mirror so you can fit your fingers in. theres 2 clip thingys at the bottom of the glass (behind the mirror), 1 on the center right and 1 on the center left so just get the screwdriver/fingers in there and push it out 1 clip at a time

if you use the screwdriver you might wanna put some rubber or somethin on the head so theres less chance it'll snap the glass...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...