Jump to content
SAU Community

Recommended Posts

Got my 1996 Series 2 M-Spec for sale, 170 000 on the clock. May cosider Swap for something else, possibly cash my way depending what it is. :)

Mob is: 0430 349 254

Located : Brisbane

asking $13 000 ONO

Email: [email protected]

gearbox and diff oils done approx 10000 ago

clutch fluid done 3 months ago

Brakefluid (dot 5) - 6 months ago

Powersteering fluid - 6 months ago

New Cooland - 6 months ago

New timing belt/Pullies - 1 yerar/20 000km ago

New Fan and A/C Belts - 2 months ago

Rocker cover gaskets - 6 months ago

Upper Engine cleaned - 6 months ago

3" Jasma Aproved Turbo Back Exhaust - complies to the law -under 86 db!

Monsta FMIC - only installed 2 weeks ago

Apexi SAFC (Super Air Flow Controller)

Exedy Racing Clutch, 8 puk ceramic material with over 1 ton of clamping force.

Drift Power intake pod filter, enclosed by a Custom fibreglass cold air box to make it legal, and gain more power.

Red Silicone Vacume lines

Blue Rocker covers

NGK Iridium Plugs, less than 10 000kms old.

New Oil Catch Can

Apexi RSM-G (Rev Speed Meter with G-Sensor, for power calculation, and 1/4 mile times, plus a heap more!)

Nismo Clear side indicators

12" Sony X-Plod Sub

1200w Boch Mann Amp

6' MTX splits in the front

Pioneer USB/Aux in headunit

Boot has been recoloured in Blue

Has had custom painting on the side skirts and front and rear bumpers

AutoMeter Boost Gauge

AutoMeter Air/Fuel Gauge

Apexi Turbo Timer/voltage display/air fuel display.

Runs 10psi, never been run over that, but is capable of it!

All interier is in almost new condition, rear seats never used, and front seats always covered

Custom Plates, black on white CME-33.

17" Precedo Racing Rims

New Federal SuperSteel 225 Width tyres on the back

New Firenza ST-03 225 width Tyres on the front

Tein Damper adjustable Coilovers

Also:

4 x 16" Origional Skyline rims in black, all with good tyres

4 x 16" Tyres, 2 almost new, 2 ok

4 x 17" Falcon rims in black, all with tyres, 2 may need replacing to be used on road (pictured)

Front Spoiler Chin, is damaged by scraping

post-54349-1234173130_thumb.jpg

Edited by R33_GTST1111
Link to comment
https://www.sau.com.au/forums/topic/256295-r33-gtst-for-sale/
Share on other sites

  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...