Jump to content
SAU Community

Recommended Posts

Engine:

N1 24U block (own modifications done) race prepped

Fully balanced and blue printed

Chemically cleaned/crack tested and washed

Torque plate bored honed & decked

All new welsh plugs

Tapped oil gallaries

Fully balanced/detailed crank and grub screwed

New Ross harmonic ballancer

Race prepped crank gurdle

Shot peened/prepped standard rods with ARP bolts

Full ARP bottem end stud kit

Ross Racing forged pistons (ceramic coated)

ACL race bearings mains & rods

N1 oil pump (modified)

N1 water pump

Genuine Nissan gasket kit

Fully port & polished head

Match ported intake

Brass valve guids

Standard valves

Upgrade valve springs

Standard cams

Greddy adjustable cam gears

Gates timing belt

New genuine exhaust studs & nuts

Garrett GT3082r .82 turbo polished front cover

Braided oil lines

Speedflow fittings

Tial 44mm wastage

Ebay spec manifold modified

Greddy twin entry air intake pipe

2 x RB25 Air flow meters

4" dump pipe

4" catback exhaust

4” high flow ballistic cat

600x300x115mm Greddy style intercooler

Custom PBR clutch

Nismo lightened flywheel

Nistune ECU

Sard fuel pressure regulator

custom fuel rail

r33 gtr lift pump

044 fuel pump

2L surg tank

3/8" Aluminium fuel lines

Heap of speed flow fittings & push lock hose

Sard 700cc injectors

Alloy dual core radiator

Silicone radiator hoses

Silicone heater hoses

Exterior:

Full colour change

18x9 18x10 roh drift r's

carbon exhaust shroud

carbon top secret bonnet painted

genuine gtr front bar and gtr grill

rear drift lip

nismo b pillars

tein coil overs

Inerior:

gtr dash cluster

autometre boost guage

hybrid boost controller

greddy turbo timer

Link to comment
https://www.sau.com.au/forums/topic/256366-final-stages-d/#findComment-4420116
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...