Jump to content
SAU Community

Apexi Afc Neo, Apexi Sitc And Drift Boost Guage

JVP
 Share

Recommended Posts

JVP Grand Master

JVP

Posted
Posted

Hey guys up for sale are my bits ive purchased for my stag. Since im selling my car, these bits are no longer needed.

Apexi AFC Neo $400.00: brand new in box, never been used, still in original box.

Apexi SITC $325.00: second hand, but never been used, still in original box.

Drift Crystal series boost gauge: $85.00: brand new in box, never been used. Its a 52mm gauge, crysstal series. comes with all fittings etc.

All items have all the relevant instruction manuals and booklets.

I will post at buyers expense.

Pick up is welcome. I am in Altona Meadows during the week, and am in Boronia/Ferntree Gully on the weekends.

contact:

MOB: 0411 355 572

WORK: (03) 9809 2299 ask for Jarryd.

cheers guys.

i have pictures if needed

skysaresilver Community Regular

skysaresilver

Posted
Posted
Apexi AFC Neo $400.00: brand new in box, never been used, still in original box.

Hi Jarryd,

Negotible on price at all for the Apexi AFC Neo? I'm interested in a quick sale for the right price..

Could you please PM me pics

Best Regards,

Adrian

  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...
  • 4 weeks later...
skyline_dimi64 Rookie

skyline_dimi64

Posted
Posted
boost gauge sold.

cheers

hey mate, interested in the SITC, any room for negotiation on price?

my PM message down at moment, if u have any ideas on what

post count 10 means, also i get as error message when trying to do

PM's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...