Jump to content
SAU Community

Recommended Posts

HKS external gate $450 ono

45mm entry with 50 mm exit

comes with flanges for manifold and exhaust port second hand good working order

HKS T04e $850 ono

60mm comp wheel inducer a/r 72 front housing

65mm ex wheel t4 flange a/r 90

comes with dump pipe

these items were part of a t04e turbo kit to suit a gtr ( 500 hp capable )both good working order no shaft play on turbo and wastegate is fully functional.

Xforce rb26 exhaust manifold t4 $150

suit rb26 with allowance for external gate. Ill throw it in for free if someone wants to buy the turbo and the wastegate

Best way to contact me is (shane)0423477797 or [email protected]

(pics in west aus for sale section of this forum ill upload them when i get on the other computer tomorrow)

Edited by mrsparkle

possibly but you need to inspect the manifold you have to see if the bolt pattern is the same otherwise its possible to weld on a different flange depends how keen you are to make that noise personally i dont think its worth the effort if they are internally gated already

possibly but you need to inspect the manifold you have to see if the bolt pattern is the same otherwise its possible to weld on a different flange depends how keen you are to make that noise personally i dont think its worth the effort if they are internally gated already

Cool, thanks

i wont be able to supply pics till monday mate sorry if your really interested this is also advertised in the western australia section of this forum and there are some pics there sorry for the muck up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...