Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

All PMS recieved and replyed to, im currently out of the country at the moment. my partner is getting the head fixed this week.

will post an update of the work and new sale price of the car.

Thanks.

  • 2 weeks later...
All PMS recieved and replyed to, im currently out of the country at the moment. my partner is getting the head fixed this week.

will post an update of the work and new sale price of the car once it has been completed.. dont know how long..

Thanks.

  • 4 weeks later...

UPDATE ON SALE

Have the car back on the road now after 3 months of pain,

The following was done to the head.

Removal of head, acid diped and cleaned up, fitment of tomie valve stem guides, hks springs, all new nissan exhaust and inlet vlaves, buckets and shims,

tomie metal head gaket, all other gaskets new, new bosh plugs, New gates timing belt idler kit etc, New cam oil seals, new head bolts.

Compression tested all cylinders came up good. Oil catch can installed. New oil and new oil filter, new coolant. Notice a Factory oil cooler in front of the raditor buyer can have this hooked up.

Car will require a complete dyno as the crank sensor was moved during the reinstaling and fittment on the Z32 airflow meters sard fuel pump etc.

Car is running smooth,lil rich, gates belt is abit noisy but starting to quiten up abit as it beds in. All bolts etc tensioned at correct torque setting.

Car was polished and driven home for garage.

New Front Springs will be installed this Friday at 8am as im not happy with the current front ride hight. And Koni adjustable shocks set.

Has Two new front tires.

I have a new cat convertor sitting in my shed which may be installed this weekend or so depending on shift work.

Ive also chucked subs and amps into it so the buyer can enjoy some doof doof.

two 10ich clairon subs with 1000wat PRECISION POWER PCX 5800 amp, head unit etc.

Current mods:

Engine:

Split fire coil packs

N1 turbos,

Braded speed flow water lines

Reco cyclinder head

Tomi valve guides

hks springs

nissasn exhaust and inlet valves

tomi metal head gasket

New head bolts

Gates timing belt

Oil catch can

INDUCTION:

KNN Pods

Bosh Z32 airflow meters with Tomi Plugs

HKS Super SQN BOV

FUEL SYSTEM:

SARD Intank replacement PUMP

Standard injectors with new seals

New ryco Fuel filter

SUSPENSION AND DRIVETRAIN

Exceedy Heavy Duty performace clutch

Machined flywheel

Nismo Diff with cooling fins

New Front left and right Drive shafts

New Koni shocks adjustable all round and new king springs

18X11 Rear 18x9.5 front WORK VS RIMS

Drilled Rear Brakes

MISC

Apex'i Power FC with hand controler (requires Tune)

Nismo 320 dash 98tho on the clock

nismo steering wheel

Full nismo body

3 inch exhaust

Interior in good condition aircon in good working condition

Paint in good condition

New front bar

Stainless intercooler pipes

Oil cooler ( Not hooked up)

No rear wiper

No ABS

Nismo build number 0231 1990 model

NEW PRICE NOT INCLUDING TRASNPORTATION

$ 17500

Contact details are via PM, Email or mobile located in Townsville (north Queensland)

Car will be sold without plates as there personalised

0431301801

[email protected]

Will upload pics soon

Thanks Guys.

:)

Edited by foney

Wondering, does anyone know what the cost would be on transport interstate to Perth? Just had my VZ SV6 written off by a transperth bus running a red light on thursday and looking for a new car...

i quoted a guy just under 1800 for the car transported to perth with the car not running. Now that it is i would assume that its cheaper.

I have to sell this car soon as im possibly moving overseas with a potential new job.

I will drop to 17000,

or drop the price more however remove parts. RIMS, Computer etc.

New springs were installed friday. Ride hight in the front is now lower.

Post pics soon.

Hi,

I am interested and financial cash buyer located in Perth.

Please email me some photos of car from both sides, front, rear, interior and engine bay please.

Also as far as I am aware, all Nismo edition 1990 GTRs were produced in Gunmetal Grey. Has this vehicle been resprayed blue?

Do you have any dyno graphs or power/torque figures for the motor?

My email address is [email protected]

Thanks,

Gan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...