Jump to content
SAU Community

Recommended Posts

hi ive got a 1993 r33 gts-t thats auto and ive noticed that when i take the radiator cap off its like a milkshake, ive checked the engine oil on the dipstick and under the filler cap and its all clean, and i took the trans cooler lines off the radiator and hooked them straight to the trans cooler at the front of the motor and flushed the coolant out and refilled it with new coolant. but then it still goes like a milkshake under the radiator cap its had nothing done to the engine still got stock turbo on. the car starts straiht away everytime and it never over heats, and the car still boosts fine a never misses a beat

i was just wondering if anyone would know wat the problem is at all or if anyones had then same problem, or maybe is it possible that coolent and oil could be getting mixed together through inside the turbo, cheers

Edited by nathan0511
Link to comment
https://www.sau.com.au/forums/topic/258218-need-help/
Share on other sites

hi ive got a 1993 r33 gts-t thats auto and ive noticed that when i take the radiator cap off its like a milkshake, ive checked the engine oil on the dipstick and under the filler cap and its all clean, and i took the trans cooler lines off the radiator and hooked them straight to the trans cooler at the front of the motor and flushed the coolant out and refilled it with new coolant. but then it still goes like a milkshake under the radiator cap its had nothing done to the engine still got stock turbo on. the car starts straiht away everytime and it never over heats, and the car still boosts fine a never misses a beat

i was just wondering if anyone would know wat the problem is at all or if anyones had then same problem, or maybe is it possible that coolent and oil could be getting mixed together through inside the turbo, cheers

sounds like you blown the head gasket

Link to comment
https://www.sau.com.au/forums/topic/258218-need-help/#findComment-4441584
Share on other sites

I dont really know if you have blown a headgasket as I am sure you would be seeing Choco milkshake effect in the engine oil,that and it would be most likely overheat. My guess is that the turbo has shit itself, allowing oil to mix with the water on that end.

Link to comment
https://www.sau.com.au/forums/topic/258218-need-help/#findComment-4441595
Share on other sites

I dont really know if you have blown a headgasket as I am sure you would be seeing Choco milkshake effect in the engine oil,that and it would be most likely overheat. My guess is that the turbo has shit itself, allowing oil to mix with the water on that end.

Yeah you could be right, but the drain out of the turbo goes back to the block, So it should be contaminated too. When you start the car and leave it running, take the radiator cap off and see if there are any bubbles in the radiator.

Are there any welsh plugs in the block between the oil and water galleries? One of these could be corroded.

I wouldn't continue to drive it though, until you get it checked out.

Link to comment
https://www.sau.com.au/forums/topic/258218-need-help/#findComment-4441613
Share on other sites

yeah ive decided to get a new turbo anyway and i pulled the inlet manifold off today and notice the back coolent passage in between cylinders 5 and 6 has a bit of milkshake in it so im gonna pull the head off tomorrow and hopefully havent done to much damage to the motor ill let u know wat i have found

Link to comment
https://www.sau.com.au/forums/topic/258218-need-help/#findComment-4442051
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...