Jump to content
SAU Community

Volk Gt-c Face2

xxx200
 Share

Recommended Posts

xxx200 Enthusiast

xxx200

Posted
Posted (edited)

hi guys these were on my 32gtr

specs are

19 inch by 10.5 wide f&r

+20 offset

looks fat and tough. only a little scratch which i got quoted for $200 to fix. all 4 rims have brand new rubber which cost me over $1k.these are located in sydney/west also comes with rays wheel nuts and volk centre cap.

asking price $3500

Edited by xxx200
Link to comment
https://www.sau.com.au/forums/topic/258747-volk-gt-c-face2/
Share on other sites
dannyw Community Regular

dannyw

Posted
Posted
According the the Rays website, there is no +20 offset...

http://www.rayswheels.co.jp/cgi-bin/cgi2/s...modelName=GTC_2

yea, i talked to my friend, he didnt notice there are +20 before.. custom?? picsss!!

Link to comment
https://www.sau.com.au/forums/topic/258747-volk-gt-c-face2/#findComment-4449630
Share on other sites
mxfly Veteran

mxfly

Posted
Posted
Err... you can order Rays wheels in any offset you want when the wheels are 2 piece.

I'd suggest you check your sources for that info because that is not entirely true. Some models of Rays rims you can get any offset to the mm, some you cannot.

Link to comment
https://www.sau.com.au/forums/topic/258747-volk-gt-c-face2/#findComment-4450259
Share on other sites
Downforce Grand Master

Downforce

Posted
Posted

Check my sources? lol ok. Eugene just because you sell a lot of Rays wheels, does not make you an authoritative source either. GTC's you can order a custom offset. I left the word "some" out of my post, but in fact most Rays 2-piece wheels can be ordered in custom offsets.

Link to comment
https://www.sau.com.au/forums/topic/258747-volk-gt-c-face2/#findComment-4450453
Share on other sites
mxfly Veteran

mxfly

Posted
Posted
Check my sources? lol ok. Eugene just because you sell a lot of Rays wheels, does not make you an authoritative source either. GTC's you can order a custom offset. I left the word "some" out of my post, but in fact most Rays 2-piece wheels can be ordered in custom offsets.

Ok fair enough, now you got me curious as last time I asked about custom offsets, they told me no.

So I will check with them again on Monday.

Link to comment
https://www.sau.com.au/forums/topic/258747-volk-gt-c-face2/#findComment-4450916
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I am well aware as I did rant at him to buy a MX5, buy the 2.5 before he DIY'ed it, etc as well as do things to the holden. He will obtain a ND. It's the best of both worlds. They look great in person, definitely the best looking one. Just a matter of time now.
    • r32-25t
      NC MX5

      By r32-25t · Posted

      Remember this is the same person who said he’d never own an nc 
    • zique
      Ceramic turbine damage to engine - what did yours do?

      By zique · Posted

      ouch! how is the car now?I had sold my gtr but have been looking into some on trademe and a 260RS but I wouldnt be keen on any repairs needed on them
    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
×
×
  • Create New...