Origin Rb26det Manifold

erins · 2009-03-05T04:57:29+0000

Hey guys This was going to be used for my own conversion but since my engine died i decided to go back to stock 25. So i have this Origin made high mount GTR manifold. Purchased when i was in Japan 5 months ago, this is still brand new. Really well made, with plenty of porting and cleaning of welds inside. Im chasing $350 neg for this, extreamlly cheap for a well made non ebay spec manifold. PM or 0421524208

By erins,
March 5, 2009 in For Sale (Private Car Parts and Accessories)

https://www.sau.com.au/forums/topic/259766-origin-rb26det-manifold/

Followers 0

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign in

Already have an account? Sign in here.

https://www.sau.com.au/forums/topic/259766-origin-rb26det-manifold/

Followers 0

Go to topic listing

Announcements

Similar Content
- 5
  
  Rebuild Original Nismo Struts (R32 GTR)
  
  By T0m
  Started June 12
- 2
  
  Pipe from Greddy FMIC to Greddy intake manifold (RB25)?
  
  By jacobzking
  Started May 25
- 3
  
  [Closed] Hks rb25 cast manifold and waste gate
  
  By robbo_rb180
  Started March 28
- 1
  
  Billet Merge Collector for manifold
  
  By Predator1
  Started February 15
- 9
  
  NPboosted manifold fitting purpose
  
  By eli995
  Started February 9
Latest Posts
- Boost cut after swap(RB25DET NEO) R34
  
  By Kapr · Posted 4 hours ago
  
  Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
- Boost cut after swap(RB25DET NEO) R34
  
  By GTSBoy · Posted 5 hours ago
  
  Yes it can be adjusted so that it does not ruin the party in Nistune. But you must have the sensor connected or the ECU will be bitchier than a teenage daughter.
- Jacks that fit under GTR lips that can reach the subframe?
  
  By Milkmun · Posted 6 hours ago
  
  Agreed, wooden ramps can’t go wrong. Or buy low profile ramps ie. gktech
- Jacks that fit under GTR lips that can reach the subframe?
  
  By blind_elk · Posted 9 hours ago
  
  I find that a single 50mm plank is sufficient to raise the car to get a low profile trolley jack under the engine cross member or rear diff. Then I use a 50mm block on the trolley lift point.
- Compatible rear drive shafts R34 N/A?
  
  By RB25inside · Posted 10 hours ago
  
  UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.

Sign In

Origin Rb26det Manifold

Recommended Posts

erins

Link to comment

Share on other sites

Create an account or sign in to comment

Create an account

Sign in

Announcements

Similar Content

Latest Posts

Forums

Activity