Jump to content
SAU Community

Recommended Posts

I have finished stripping down most of my RB26 donor engine rady to build up the B30.. I noticed when I took off the Oil filters there is a slight difference between the RB30 and RB26 block?? My RB26 is from an R33 and has a water cooled oil cooler that the filter then mounts to. On the RB30 the filter is direct onto the block. When you remove the cooler from the RB26 instead of having a thread, there is a lug sticking out that is a snug push fit inside the oil cooler housing (I assume this is to direct the oil flow correctly) How do I modify my RB30 block to accept the same cooler or is it easier/better to dump it and get a relocation kit and traditional type cooler? I am sure I have seen RB30's with the RB26 type cooler so presume it's possible?

Thanks

Lee

yes it can be done, i just unscrewed the fitting out of a rb26 block that has the slot in it for the oil cooler block and used that to screw in the place of the threaded one on the rb30, it screws straight in and works same as rb26. To get the 30 one out i ground a straight into it with an angle grinder and used a thin bar to unscrew it (was damn tight, might need to heat it with any oxy to crack the seal if its really tight), the rb26 one already has a slot in it so use a piece of bar that will fit in it and do the same.

what doesnt work? do u mean pushed as in making alot of power? ive never had an issue yet with mine, i have removed it from my other motor but redoing all the water lines etc under the plenum is a pain, well harder than just screwing the rb26 oil cooler on anyway. whats a gts4 one look like?

Edited by unique1

im mean when your thrashing the car they do sweet fa in cooling the oil.

the gts4 one is angled to suit the front diff. and when a sandwich plate goes on its much easier to work with. but you will need the 26 block fitting.

basicly the same but without all the hoses and cooler in place..

im mean when your thrashing the car they do sweet fa in cooling the oil.

the gts4 one is angled to suit the front diff. and when a sandwich plate goes on its much easier to work with. but you will need the 26 block fitting.

basicly the same but without all the hoses and cooler in place..

fair enough sounds like a good idea i didnt even know about the gts4 ones, thanks for the info

cheers for the info guy's I have to say when looking at the blocks I thought the stub in the middle must be removable.. So I have two options.. Well three... RB26 oil cooler which I can see probably does jack if you are really giving the car death.. GTS4 cooler.. Is it an air cooler or water cooler?? I wasn't clear on that.. Finally get a relocation kit and fit a regular oil cooler.. I presume a 19 row regular type rad cooler would be fine for a start?? I don't intend doing heavy track use at all.. just a road toy if that helps!

I was also planning on removing some of the other junk under the inlet plenum while I am at it to tidye tings up a bit.. I hear the Idle valve can be removed and then it's a cse of joining some pipes and blanking others..

By the way T04GTR.. What is the car in your avatar?? I can't make up my mind!? looks like a beast anyway..

DR30?? I am guessing that is a very early liner?

Anyway. When you say the relief valve in the block I oresume you mean the bit that looks like a ball bearing? I wouldn't have enven considered removing it!

So basically it's a sandiwch plate of some sort and relocation kit or cooler kit.. 19 row not worth bothering with?? Only ask as they seem to be very common and easy to obtain!

Thank you

Lee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...