Jump to content
SAU Community

FS: Reflective Silver Window Tiniting Flim

Advan_01
 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

Basically, no .. only 3/4 ...of course you need the rear to see the road.. and it can't be reflective. see below..

Windows

All windows of a motor vehicle, other than windscreens, available to the driver to obtain a view of the road or other road users must have a light transmittance of at least 35 per cent. However it is desirable that the light transmittance of windows to the side and ahead of the driver is not reduced below 70 per cent.

Note: Windows above or behind the driver's seating position on some buses are not in the drivers field of view and need not comply with the above light transmittance requirement.

The reflectance of any window fitted with tinting film must not be more than 10 per cent (which effectively is the same as untreated glass).

A vehicle fitted with a tinted windscreen or window which is not in accordance with the requirements set out in this information sheet is unroadworthy, and subject to the consequences thereof unless the vehicle has been constructed for a special purpose and has been granted exemption from these requirements by VicRoads.

Redback Proficient

Redback

Posted
Posted

predator666, were do you get all the unroadworthy information. i went to the cop shop and they told me shit. transort sa i think dont even want to know me.:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      The answer to this would be I followed the documentation from Turbosmart which said each spring pressure could achieve a maximum of 5x it's rated pressure so the included smallest spring being the 6psi had a range up to 30psi. I went with the 12 because I figured it'd likely hover around 15psi as a base pressure however I was obviously wrong.    I have a log here that I'll dig out that is purely wastegate and no Mac valve controlling anything.   If it can't hold anywhere near 12psi, does that mean the straight gate is virtually wide open during a run? Or am I thinking about this all wrong.   I could Tee Piece into the cooler pipe pre intercooler where the wastegate gets its feed, and send that to the ecu and see how that reads, I just don't have a spare pressure sensor currently that's all.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      lol nice, I wouldn't worry about sanding back the filler to check for rust then. Yep very much a thing. Personally I don't do the panel beating, its very easy to have a panel beater sort that out for you. If they aren't doing any prep work the actual panel beating generally doesn't take long at all.  Have you taken before pictures before you started this project? I'd be keen to see the before and afters when you're done.
    • Lithium
      Borg Warner EFR Series Turbo's V 2.0

      By Lithium · Posted

      Some good discussion in here, for the most part I can't really add too much to it - thought I'd add some notes to the datalog screen shot that probably aren't news to anyone but a good prop... this is assuming 25psi-ish should be the boost ceiling given the first post refers to 23psi.   To state the obvious, this issue seems super weird.  Turbo speed seems pretty lethagic to build, like the turbo isn't getting as much drive as it needs - and it doesn't help that wgdc keeps rising AFTER boost target then completely shuts duty at a point, which in theory should have the straight gate dump heaps past the turbo and funnily enough causes the huge drop off.  It seems like pretty blunt boost control tuning but I'd not call that the primary issue, so much as possibly not helping the situation. I'm curious, what does a pull look like with purely mechanical boost control?  Like purely wastegate?   There are things in this log and story that make it sound like there could be a significant restriction in the intercooler piping or something - but then it's also overshooting boost target which is NOT what you'd expect with a restriction.   I can see where people are coming from with the non-linear wastegate bypass (not that any valves are linear for this kind of thing), but it still doesn't make sense that it can't hold <20psi on a 12psi spring.    Have you, or can you try measuring pressure pre-intercooler?  Be pretty interesting to see what's happening there vs in the intake manifold - sorry if I've repeated old ground, I've kinda skimmed over but I could have missed something.  In terms of comments regarding the wg spring being closer to boost target, I haven't used a straight gate but part of the reason for having close to wg target is about fighting backpressure as well - I might be wrong, but I'd have thought that part of the point of using a butterfly valve like the straight gate does you actually don't have to resist pressure at all, on EITHER side of the gate.   It shouldn't need too much leverage to start opening, the spring being more to do with where it triggers opening as opposed to resisting boost & EMAP, though smarter people can correct me if I'm wrong there.  
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ah the car is a complete shitbox and not even worth a respray lol, for a professional to do it would probably cost 15k because of all of the dings and stufd but I was keen for a side project. Also solved the problem of being bored haha. But with the rust yeah I can always fix that in the future, not a huge issue for me. I found out yesterday that when a dent is created a high spot is created around it (the crown) and to fix it I either need to tap the edges or just sand over it. Which is what made my filler work a bit confusing originally lol.
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      That's some useful information to have , it would be great if we had more local suppliers .
×
×
  • Create New...