Jump to content
SAU Community

Recommended Posts

hi every body :)

i am thinking of buying a cheep cat and hollowing it out and then welding in a pipe so that i dont get flow stagnation and so if i get pulled over and a cop checks under the car it will look like the cat is still there.

and i will keep the old one so i can put it back on if i have to go threw the pits.

what dose every body think

will i get more power?

has any body else done it?

Link to comment
https://www.sau.com.au/forums/topic/260780-a-quick-exhaust-question/
Share on other sites

You mean... decat.

Flames, etc.

It's awesome. Don't listen to Greenpeace. Just do it.

And I have a cat on my GTR and I still get black shit all over my rear bumper... runs rich. You'll get black shit regardless if you have a cat or no cat.

Edited by CRoNic...

thx CRoNic... for that explanation about black shit

i was thinking like what the f**k black shit why

i will see if i can pick a old cat for cheep probs next week

any ideas ?

i was thinking of checking the quokka and if that is a no go i will check out wreckers

possible cop trouble, and heaps of black shit all over your car.. for a couple of kw? you gotta be kidding.

just buy a decent hi flow cat mate...

my 2c

im with him on this case.

I hate it when cars dont have cats in them. They smell like shit.

I have a cat in mine and i can safely say i have no black shit @ all on my rear bumper.

All the cars ive seen with no cat or that is fitted with a decat does.

Do the right thing by ur car and get a hi flow.

just to put some myths to bed regardings exhausts and cats etc etc. In all but extreme power uses there is no need for huge catless exhausts.

As gases cool they contract and as such the requirement for hight flow rates reduces. The times that cats do get hit by masses of flaming hot shit is normally when you close the throttle and rich spot travels down the exhaust. I think most people will agree that during lift off is one time when your really not going to give a crap about exhaust restrictions.

Just get a good high flow and inconjunction with a good exhaust and you'll be just fine.

Just that if you're running a rich tune, it can cause the cat to become blocked and not work properly, which then isn't diagnosed until the exhaust starts leaking out of every possible little gap lol.

So run a proper tune and recoup the cost of a cat and your tuners' time in a few weeks.

Honestly if you run rich enough to bugger a cat you are a f**king moron wasting fuel wasting power and wasting money! Get it tuned.

I had a friend with an EVO4 who ran so rich we used to get on the radio after he gave it a hit and go "thanks mate my fuel gauge just went up!". His engine needed a REBUILD 6 months later.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...