Jump to content
SAU Community

Recommended Posts

hello all, now i admit i am new to cars and turbos and stuff and probably dont know wat im on about, but i havea hks ssbov and everywhere i go people seem to be bad mouthing it becuase it apparently makes ur car stall and shit like that.

now i went through those problems as well, but i later found that wen having a hks ssbov u are also required to have a hks idle stabaliser, and wen i got that in, everything worked like a charm!!!!!!!!!!!!!!!!!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/
Share on other sites

Flutter is not from the BOV it is from the air flowing back through the turbo. It's not good for the turbo at all. Obviously by over-tightening the BOV you're gonna end up with the air going thru the turbo as it can't vent, hence the flutter.

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-553759
Share on other sites

One of the things about Jap BOV's is that unlike ones from Oz they aren't all simply products of the metal laythe....A lot of Jap ones are actually cast items, this is why they are far more expensive. From memory the HKS Sequencial BOV is not adjustable, I had one a long time ago on my starlet. The Super Sequencial is though.....then of course there is the Super Racing BOV from HKS, now that's expensive :)

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-553810
Share on other sites

As I said I don't think you can adjust the older one. If yours has adjustment then what it does is put more pre-load on the actualto spring insied the bov and makes it hard to force open, you do this if you run higher boost (set it soft for low boost cars and hard for cars with much higher boost) The basic rule of thumb is set it hard so you hear the flutter then back it off till you can't here it any more ..... that should be the right setting.

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-554179
Share on other sites

because the SSQV as 2 valves, the smaller purple pointy thingy and the bigger valve with the HKS wordings...the screw only adjusts the tightness of the big valve.

i've yet to solve the damn fluttering problem because of this...no matter how loose i turn it.....it only affects the bigger valve...

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-554679
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...