Jump to content
SAU Community

Recommended Posts

hello all, now i admit i am new to cars and turbos and stuff and probably dont know wat im on about, but i havea hks ssbov and everywhere i go people seem to be bad mouthing it becuase it apparently makes ur car stall and shit like that.

now i went through those problems as well, but i later found that wen having a hks ssbov u are also required to have a hks idle stabaliser, and wen i got that in, everything worked like a charm!!!!!!!!!!!!!!!!!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/
Share on other sites

Flutter is not from the BOV it is from the air flowing back through the turbo. It's not good for the turbo at all. Obviously by over-tightening the BOV you're gonna end up with the air going thru the turbo as it can't vent, hence the flutter.

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-553759
Share on other sites

One of the things about Jap BOV's is that unlike ones from Oz they aren't all simply products of the metal laythe....A lot of Jap ones are actually cast items, this is why they are far more expensive. From memory the HKS Sequencial BOV is not adjustable, I had one a long time ago on my starlet. The Super Sequencial is though.....then of course there is the Super Racing BOV from HKS, now that's expensive :)

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-553810
Share on other sites

As I said I don't think you can adjust the older one. If yours has adjustment then what it does is put more pre-load on the actualto spring insied the bov and makes it hard to force open, you do this if you run higher boost (set it soft for low boost cars and hard for cars with much higher boost) The basic rule of thumb is set it hard so you hear the flutter then back it off till you can't here it any more ..... that should be the right setting.

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-554179
Share on other sites

because the SSQV as 2 valves, the smaller purple pointy thingy and the bigger valve with the HKS wordings...the screw only adjusts the tightness of the big valve.

i've yet to solve the damn fluttering problem because of this...no matter how loose i turn it.....it only affects the bigger valve...

Link to comment
https://www.sau.com.au/forums/topic/26090-hks-ssbov/#findComment-554679
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...