Jump to content
SAU Community

Recommended Posts

i have a r32 gtst bonnet has been cut to look like a gtr bonnet

only bad is

its been cut under the bonnet

the last car it was on must of had a intercooler pipe in the way

so its been cut to make it fit

other then that

bonnet fits perfect

ready to paint

200$

0401906086 call or msg me if interested

post-58084-1237013108_thumb.jpg

post-58084-1237013119_thumb.jpg

post-58084-1237013134_thumb.jpg

Edited by christian69
Link to comment
https://www.sau.com.au/forums/topic/261084-r32-gtst-cut-to-gtr-bonnet/
Share on other sites

ill give u 50 buks no more theyre going for $60-100 on ebay painted in e.c....If u want ill come pick it up whenever u want. Let me know. 0401 099 025

there is 2 gtst bonnets one for $50 and the other starting bid at $1 lol This bonnet is stuffed and isnt legal so isnt worth much...$50 thats all im offering.

There are some other bonnets going more exp. but are in E.C. This ones been hacked at.

lmao me to

iv seen a r32 gtst bonnet STARTING BID 50 lol

could go up to anything

that damage is easy to fix

my mates gota stufft gtst bonnet

i can get it off him an cut the part i need out an weld it

easy job its just

who has the time these days

like i dont mind if the bonnet stays with me

BUMP 100 bux people

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
×
×
  • Create New...