Jump to content
SAU Community

Recommended Posts

Congrats Rob and Co! You must be rapt :blink:

He ran 4 7s at a meet today at Meremere NZ, all at around 176mph and the fastest of which a 7.89 @ 176mph (basically in limiter in top gear) after tuning the car for a bit more boost this week. Still running the Nissan crankshaft!

What is the fastest RB30 powered drag car anyone knows of?

Link to comment
https://www.sau.com.au/forums/topic/261181-rips-240z-into-the-7s/
Share on other sites

And what is the minimum for the next class you're looking at?

Is there any point selling the zed? Since you've come so far wth it, if all it needs is new ratios and a trip to weight watchers - wouldnt you want to see just how far the little datto can be pushed? :P

And what is the minimum for the next class you're looking at?

600kg minimum for the next class we'll have the motor in (but it'll probably be around 750kg all up) and then 765kg minimum for the class we intend to run after that or if we go back to Pro Import 1060kg.

Is there any point selling the zed? Since you've come so far wth it, if all it needs is new ratios and a trip to weight watchers - wouldnt you want to see just how far the little datto can be pushed? :thumbsup:

The 240z is a street car (missing headlights, wipers and a muffler, it has a 6 point street cage, glass, full dash etc, its short, it has a high COG and it has done more than I ever thought it could do, its time to get the motor into something purpose built.

Rob

What the hell is in the r32 at the 4min 18sec mark?

Another RIPS RB30'd car?

Nah, it belongs to Joe Kyle (aka Yoda) - a lad who runs his own shop in West Auckland and been around with that car for ages. If I remember rightly it runs a fully built stock displacement RB26DET with a T51R SPL on pump gas and full normal street tyres, he's not a forum goer to my knowledge or anything but its a very very tough streeter.

Edited by Lithium

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...