Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

on a side note, anybody know where I can get a gasket for the plenum? thining of putting the greddy one on this weekend.

Does it bolt onto the stock runners?

If it does you prob wont need to replace it, I just did mine last week and the gasket that was on there was fine.

Edited by Danski
Ah ok

Have you bought it yet?

yeh. bought it back in jan, along with my turbo kit. just haven't had the cash to strap it all on. been waiting to buy some injectors and an afm before it all went on. but bought some rims last week, so won't be putting the turbo on till probably next year. so may as well strap the manifold on now.

Fags can't come tonight because shitty uni assignment is due in on Monday. Guards are getting rolled tomorrow and if all goes well the car will have new suspension in by the next meet :P

Fingers crossed

yeh. bought it back in jan, along with my turbo kit. just haven't had the cash to strap it all on. been waiting to buy some injectors and an afm before it all went on. but bought some rims last week, so won't be putting the turbo on till probably next year. so may as well strap the manifold on now.

So youve got a new intake manifold and plenum?

queer... u mean more like..

gonna hang out with those my native bros sharing a goon bag? then after we trashed drunk might fill up the bag with paint walking around town asking for a dollar

lol

collin you fit my sticker yet? its hawt

Edited by Redsuns88

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...