Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

f**k me josh!

thats jizz - when i have cash for wheels, we'l talk offset :D

Soooooooooooo very very hot. Almost makes me tempted to pull apart my rims to rebuild them for porn fitment, but alas I am a very lazy kid. In past history tells me anything, they'll never go back on my car :/

i bet thats something u'd do

It’s actually pretty common to do a flip/conversion as it’s cheaper than getting custom made lips/barrels made. Pretty common in wheel rebuild threads on a few of the wheel/offset forums I am on.

Yes I post on wheel specific forums

Been wanting to do the same thing:

http://www.skylinesaustralia.com/forums/Ca...-S-t273284.html

Also went and spoke to a shop in Underwood that do a few race cars/drift cars (they did the body work on the Option1 Silver 350z). Without sitting down at working out each cost, they said around $1000 to weld in a pannel.

I have seen roof cuts on ebay for as little as $150. Cut at the pillars, so easy to match and cut, then re weld. People are put off, but I don't know why - People take the roof off cars for SERIOUS roll cage building, it's not different - Your just replacing it with another one.

IMHO if anything putting a sunroof in a non sunroof car makes a car weaker then welding in a non sunroof, roof.

IMG_88461229636234.jpg

padovers%20roll%20cage%20spagetti%20porn1229628611.jpg

roll%20bar%20pipes%20fitment%20before%20welding1229433236.jpg

that's a bit better. thought 2k was a bit rough.

do you know if you could fit the non sunroof roof lining once the work was done?

what place in underwood did you see? i work near there, so may pop around and have a chat

wow just went an met my next door naighbor who ive seen playin around in his garrage the past few days, hes got a r31 with a rb26/30, gt3582r, 4" zorts turbo bak ful surge tank setup, big f*k off external gate, the whole f**kin shabang.

Full good dude, Hoping to get it going for powercruize.

that's a bit better. thought 2k was a bit rough.

do you know if you could fit the non sunroof roof lining once the work was done?

what place in underwood did you see? i work near there, so may pop around and have a chat

Yeap, the more you supply the cheaper it is. I just wanted a sheet welded in with no centre rib (IIRC its only there for two reasons to hold in the roof light and to stop minor roof flex eg: if you lent on the roof in the centre).

If you supplied the centre rib and hood lining and just welded in a plate, apposed to a full roof swap it'll only be around the $1k as well. You can buy the rib new from nissan. I'd also take the sunroof out myself as thats an extra few hours labour you can save. I've had mine out heaps, it's not a hard job.

The shop is in Kenway Dr. Should be building number 6. There is always imports and all kinds of shit there.

**the hood lining on my non sunroof R32's where only ever held in by the side pillar trims, no clips, no glue. There is no reason why a factory liner will not fit**

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...