Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

52mm alloy dual core rad has arrived with new piping!

cbf putting it in.. might way for it to either shit itself or new engine transplant..

looks huge.. i dont think there will be much clearance or fk all actually for clutch fan and shroud

52mm alloy dual core rad has arrived with new piping!

cbf putting it in.. might way for it to either shit itself or new engine transplant..

looks huge.. i dont think there will be much clearance or fk all actually for clutch fan and shroud

So you're the one trying to get rid of the radiator...

I'm looking at getting the 40mm one from justjap.

BAHAHAHAHAHAHAHAHAHA just went out to test out the Bee*R flatshifting mode.

Got literally 10m from my driveway and saw a cop car in the driveway of the golf course

so, quickly turned it off, did a lap of the block, and went back in to the garage. Sirens on, cop comes up for RBT.

All good, blew 0. She was actually quite nice, had a bit of a chat. To be fair I would have looked really suspicious :). Might stay out of trouble for the rest of the night...

f**k you and your good luck martin. if that was me i'd be arrested for sure.

Thats because you would have:

Dan says:

should have just shut [the garage] and run out the back door

i think i would be the heaviest out of the thursday crew, with a lazy 115kg

somebody is welcome to prove me wrong

encouraged even

i heard dave was writing you off, saying he weighs more, you aint shit and packs a meaner punch...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...