Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Im going deep sea game fishing on sunday. So neg from me!

Might re-wire the garage tomorrow for 15amp power, its not hard at all.

Today was shit, left home at 6:50am drive 26km to work arrived at 8:10am. Stupid traffic light failure..... then into a day that was crap, non-stop work from 8:10am until 5:40pm no lunch even

wow... seems everyone had a shit day.

except me. I woke up at 1pm, lounged around, watched some simpsons, went to the video shop, went to the comic shop. Ate some snacks. Was tres awesomeness :cheers:

I have had a couple beers now, steak for dinner, and im sitting in front of my computer wearing my tatical vest and my bandoliers, I need a WW2 or Vietnam era US army combat helmet now

wow... seems everyone had a shit day.

except me. I woke up at 1pm, lounged around, watched some simpsons, went to the video shop, went to the comic shop. Ate some snacks. Was tres awesomeness :cheers:

get a job you bum! hahaha. I wonder what is with today? Everyone i know had a shit one, including myself. Global warming i guess? S'all good for me, im on holidays now, anyone want cheap parts from japland while im up? haha

Might re-wire the garage tomorrow for 15amp power, its not hard at all.

put a 10amp plug on the lead, plug it in to a pwr circuit make sure you dont use anything else on that circuit while the compressor is going.

otherwise 1x15amp pwr point with a 2.5 back to the switchboard on its own circuit.

be dodge and use the first way, i do on my welder :cheers:

yer, i been told no Mr. Home electrician for me, so parents are getting a sparky in next week, its their garage.

yer, i been told no Mr. Home electrician for me, so parents are getting a sparky in next week, its their garage.

guarantee my cashies are cheaper :cheers: then said sparky.

Many thanks Tas.

Install on the AVCR was nice and neat and done way before you said it was going to be ready.

Done well. Very happy.

:P

No problem at all matey! glad u enjoy it!

Gebus it is ded.

Whats hapenning mangs ?

Work + hangover = sucks balls

f**k that, it sure does.

Bout to go up the coast to pick up my new front bar... tsunami? Hmmmmm........ :blush:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...