Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Nah it turns too well. It is very twitchy up front. That and it bounces over the road with all the uneven surfaces in the mountains.

Sounds like it could have some epic toe out

think i might have to cut down my drinking.....

nnnaaaaahhhhh

It wouldn't suprise me if it did. I'm getting more circlip grooves machined into the bilsteins so I'll be able to lower to rear more once the suspension is in ill get a wheel allignment done.

dude its a 31 - lower it with an angle grinder

I was going to and I had everything ready to go on Sunday but when I got the springs off I found that they had the same circlip height adjustment as the GTR so I may aswell get it done properly. Saves it handling like a piece of shit and destroying decent shocks.

So the 31 has number plates now. I drove it home through the mountains

YES YES YES YES

Same as before. It doesnt go off the scale it just stays at like 3/4

just a thought - what about picking up an aftermarket water temp guage??

when my 180 decided to spit out its heater hoses at a track day my water guage jumped to 110degrees - whereas my guage on the dash was at like 3/4 - surely it should have been maxing out :down:

Same as before. It doesnt go off the scale it just stays at like 3/4

Oh is that all? That's only...90? that's no biggie :) just pretend it's not lying :down:

and is that running coolant or water to get so hot you can smell it?

Edited by Isola
Oh is that all? That's only...90? that's no biggie :D

On a 31 3/4 could mean anything from 45deg to 245deg :down:

Bah Colin DID get his licence back before i got my car back :( ha ha

Don't worry, he'll lose it again before you get your car back too :)

YES YES YES YES

just a thought - what about picking up an aftermarket water temp guage??

when my 180 decided to spit out its heater hoses at a track day my water guage jumped to 110degrees - whereas my guage on the dash was at like 3/4 - surely it should have been maxing out :P

will be getting some gauges for eventually. I dont trust the standard ones at all.

Oh is that all? That's only...90? that's no biggie :D just pretend it's not lying :P

and is that running coolant or water to get so hot you can smell it?

Combination of both really.

Bah Colin DID get his licence back before i got my car back :( ha ha

:)

On a 31 3/4 could mean anything from 45deg to 245deg :P

Don't worry, he'll lose it again before you get your car back too :P

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...