Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

speaking of sammich its time for lunch!

building mum a computer today out of spares, although i did buy her a new video card, its more powerful then my old one :woot:

anyone got a 120mm hole saw they can lend me? new PSU needs to vent out of the case

getting hungry too. ducked out from work early.

managed to get myself into a bit of a pickle with our friendly constabluary

will update as events unfold today

did they find a "cop" In your boot. ;)

a freshly butchered one :P

will just update everyone on thursday, this being a public forum and all

don't think it will trump isola's story tho. that was a crackup

I need to borrow r34 LH & RH mirrors for compliance.. PM me if you can help

How can you borrow mirrors ? ;)

More importantly if you guys want to have a look at some... a lot of skantly dressed women pull up a chair on racecourse rd around 430pm. There was so many heading up that way about a hour ago... :P

Evening all

How can you borrow mirrors ? ;)

Somebody may have a car in a workshop getting work done or car could be off the road for some reason.

There are endless possibilities but i will leave it there.

SW11075-00-01.jpg

they have white faced ones as well with red dials, but thinking of sticking with black as it will match my standard cluster

def stick with black.

They look pretty sweet. I approve :)

+1

How can you borrow mirrors ? :worship:

More to the point... how do you then get your complied car roadworthy once you've given the mirrors back? and if you get it roadworthy THEN give the mirrors back... how do you not wind up getting defected to the Nth degree? Sounds like a foolhardy plan to me.

compliance is alot more strict then a roadworthy john, when a car comes into the country for compliance these days it's got to be pretty much 100% stock.

For a roadworthy you just got to have side mirrors of flat glass, nothing special. Guessing this 34 has aftermarket ones?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...