Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Morng mangs!

Anyone know the size of the stock RB25 turbo inlet? Is it 2 3/4"?

How hard is it to get some piping that will go from the stock intake up to 4"? Don't know the first thing about where to look. Or could I just use a silicone joiner that goes from my intake pipe -> 4" inlet on a new turbo?

Morng mangs!

Anyone know the size of the stock RB25 turbo inlet? Is it 2 3/4"?

How hard is it to get some piping that will go from the stock intake up to 4"? Don't know the first thing about where to look. Or could I just use a silicone joiner that goes from my intake pipe -> 4" inlet on a new turbo?

Just about any performance shop should be able to make up something for you.

I don't think you'll be able to use a silicone joiner as the stock intake pipe is plastic. If you use a pod you MAY be able to clamp the stock intake onto a short bit of ally the right size then use a silicone joiner to bring it up to 4". But that will be a big restriction in the inlet...

over 9000

This.

Morng mangs!

Anyone know the size of the stock RB25 turbo inlet? Is it 2 3/4"?

How hard is it to get some piping that will go from the stock intake up to 4"? Don't know the first thing about where to look. Or could I just use a silicone joiner that goes from my intake pipe -> 4" inlet on a new turbo?

you can slide a 2.5" pipe over the inlet nicely. I did this with my old setup on the Telstar. Cut 2 slits in the pipe and clamped it to the inlet.

I cant find a pic of it, but if I do I'll post it up.

short bit of ally the right size then use a silicone joiner to bring it up to 4"....

Marto's penis enlarging tip #103

col goes to toowoomba this morning early left home at 4am...

col does his days work with the hope of getting home early to play ps3...

a piss load of rain falls, tbar range get closed due to land slide...

i take the DR route, so does everyone else...

get back to the highway some hour later, its flooded over at Heliden...

col gets home at now whe i left there at 2pm :(

Wait.... oh

How does getting whacked in the testicles affect your right hand...... oh

FKN LOL

col goes to toowoomba this morning early left home at 4am...

col does his days work with the hope of getting home early to play ps3...

a piss load of rain falls, tbar range get closed due to land slide...

i take the DR route, so does everyone else...

get back to the highway some hour later, its flooded over at Heliden...

col gets home at now whe i left there at 2pm :(

I also hate rain and being in places that require some travel. I'm lucky I wasn't in Rocky a day later than I was, otherwise I'd still be there.....

im lucky i left my girlfriends place when i did. 2 days later the weir river cut the road so now the skyline would have no chance of getting out, i need a 4wd

@Colin: Contact this guy: http://motamota.r31skylineclub.com/index.php?topic=132962.msg1525770#msg1525770

Also @ Colin: I put fuel in the Pergeot, it took almost 55L and wasn't even empty yet. So yeah, it just has an epic big tank for a small car.

Also @ Colin: Are your rims 4/5 stud or just 4 stud? I may actually be interested if they are 4/5...

So we could get 5% off if we get 4 turbos high flowed at te same time by hypergear. He starts back at work around 8th feb...

Also @ Colin: Are your rims 4/5 stud or just 4 stud? I may actually be interested if they are 4/5...

I don't know about Colin but I'm 100% stud ! LOL

So we could get 5% off if we get 4 turbos high flowed at te same time by hypergear. He starts back at work around 8th feb...

Well that's like $50 off, which is not bad, but not good enough for me to wait around till the end of January. I'd rather pay the extra $50 and get my car back on the road sooner...

So if you can sort out your four so we can send them off next week them I'm in, otherwise I'm out.

Thanks Dude :)

@Colin: What was the name of that tuning place you were telling me about?

It doesn't matter if you wanna pay more or not, he's not back at work til the 8th

Unless you were talking about someone other than hypergear?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...