Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

When replacing my turbo, what gaskets do I need?

I'm thinking:

Manifold-> turbo gasket

Turbo->dump gasket

Oil return gasket?

Am I right that the oil feed doesn't need one?

Manifold-> turbo gasket

Turbo->dump gasket

These. Althought they are fairly sturdy gaskets and if they are in good nick you might be able to re-use your current ones.

Oil return gasket?

Should just be able to remove the oil return hose so shouldn't need a new gasket here.

Am I right that the oil feed doesn't need one?

You should replace all the banjo bolt washers on the oil feed/water feed/water return. That said, a lot of people probably don't bother, but they are not very expensive so I would.

Just take the banjo bolts to enzed or something and ask for banjo washers to suit.

What exactly IS a banjo bolt?

TJ-SS07.jpg

There will be one on each end of you oil feed line, water feed line, and water return line. So 6 banjo fittings, needing a total of 12 washers. The sizes will vary, (some will be the same some different) so you will need to work out the sizes you need when you pull it off and then take them in and say "I need 4 of these ones, 8 of these ones..." etc.)

The oil return line is just a normal clamed hose. I can't remember 100% but I think the gasket you are talking about for that one is where the hose fitting connects to either the block or the turbo. But you don't need to undo it there, just undo one of the hose clamps and take the hose off.

EDIT: That picture is a little misleading, the washers are not actually copper washers but 'banjo washers'. According to the dude at Enzed when I went anyway...

Edited by Smity42

Ok so I -might- be able to re-use those washers, depending on how they look when they come out?

Should I drop my oil before I do this? Or will it just be a small amount of oil that comes out of the feed?

I should drop my coolant though, yes?

Ok so I -might- be able to re-use those washers, depending on how they look when they come out?

Should I drop my oil before I do this? Or will it just be a small amount of oil that comes out of the feed?

I should drop my coolant though, yes?

You are NOT supposed to re-use the washers. They crush when you tighten the bolt and that is how they seal. Once crushed you are not meant to re-use them.

I think some people do though, but its a bit dodgy, and you may end up with leaks.

It might only be 31 owners that re-use them...

Should be no need to drop the oil, just let the car sit for a while so that most of it drains back to the sump before you do it. You may spill a small amount but nothing much.

Water... Can't remember. You will probably lose a fair bit of it so put a drain tin down, but theres probably no need to drain it entirely. Just fill it back up and bleed it when you're finished.

Been shut for a while for the airport link work. Maybe it was only through certain hours...

Did not know that. Must only be certain hours...

The oil return line is just a normal clamed hose. I can't remember 100% but I think the gasket you are talking about for that one is where the hose fitting connects to either the block or the turbo. But you don't need to undo it there, just undo one of the hose clamps and take the hose off.

I meant on the turbo where the oil return goes in (i think thats what it is, not sure) there's like a flat surface area around the hole - looks like it needs a gasket.

Burson have a turbo gasket kit with 2 metal gaskets and 'about' 4 cork ones for $50. No washers.

What's the enzed place you mentioned?

Edited by mosquitocoils

I meant on the turbo where the oil return goes in (i think thats what it is, not sure) there's like a flat surface area around the hole - looks like it needs a gasket.

Ahh... if there is something there that you have to transfer from your old turbo to your new that needs a gasket, then yeah you will need that.

Burson have a turbo gasket kit with 2 metal gaskets and 'about' 4 cork ones for $50. No washers.

NFI what those cork ones would be. Pics?

2 metal ones would me manifold-turbo and turbo-dump I reckon.

What's the enzed place you mentioned?

enzed (http://www.enzed.com.au/) or pirtek (http://www.pirtek.com.au/) or any other hose joint really. I didn't get a mobile guy out, I just went into a store.

been up in the copper today again, brisbane is a sea of activity...

people, cars, trucks everywhere...

seems business is back to normal for the major shopping centers...

hope the people who bought 20 loaf's of bread die eating them, wankers...

Ahh... if there is something there that you have to transfer from your old turbo to your new that needs a gasket, then yeah you will need that.

Yeah I'll just suss out what I need to re-use when I get to it I guess.

NFI what those cork ones would be. Pics?

2 metal ones would me manifold-turbo and turbo-dump I reckon.

Twas over the phone my good sir so no pics, but I was guessing the same as you.

So, good thing no one went to old Baskins last night...

XF and 33s would have gotten across that...

Are we allowed to pick women folk in the mens cricket team? I reckon this Elyse Perry chick bowls better than ANY of the blokes do...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...