Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I was fine when I was waiting for parts and waiting for them to be installed. It's knowing that it's all back together and all working and driving just fine (just not as efficiently as it could) that is killing me.

Well fret no more. They now have it. Not sure that it will be done today but it's turtle-heading

Well fret no more. They now have it. Not sure that it will be done today but it's turtle-heading

You just made my day Dan the man!

*Does a happy little dance*

Reckon I'd be fine to swing down tomorrow arvo to pick her up?

It's got a new Nistune ECU in it.

Good choice :thumbsup:

Nice power from a lightly modded 25 I must say :) I'm going to be happy if I get around 180-200rwkw.

Yeah really happy. People have got around 250rwkw @ 18PSI out of the same turbo, but probably have a less restrictive intake. Also i believe EFI's dyno reads a little on the low side. So I'm stoked.

So, seeing as it's driving so great, you going to come out for a drive to Jacks?

So I can hard park it? Negative. I've got to go round to Dave's to pick up a shroom for Scott, and help (read: supervise) Dan getting Dave's clutch working.

Yeah really happy. People have got around 250rwkw @ 18PSI out of the same turbo, but probably have a less restrictive intake. Also i believe EFI's dyno reads a little on the low side. So I'm stoked.

It does read a bit lower than most, at the majority of places around you would make 10 to 15rwkw more i reckon.

I've got to go round to Dave's to pick up a shroom for Scott, and help (read: supervise) Dan getting Dave's clutch working.

Don't think Dan can make it now. It's not like I need to drive the car to work tomorrow or anything :whistling:

It does read a bit lower than most, at the majority of places around you would make 10 to 15rwkw more i reckon.

Which would put it pretty much bang on that 250 mark :).

Don't think Dan can make it now. It's not like I need to drive the car to work tomorrow or anything :whistling:

Roger. I'll swing round anyway and grab 'shroom.

Noel if you go to Jacks let me know, It will give me a good reason to clean my car

yup, no work again tomozz so Fat Alvin will be rollin in...Be hatin

Village square it's called. Enter carpark beside JB-HIFI.

I laughed fairly hard at the idiot who ripped the bottom out of his super low S13 about a month back. He tried to cone in over the big speed bump at the other side :P

hey does anyone have an r32 actuator (10psi) and if they want to give or sell (but mostly give) can they please bring it to baskins tomorrow? or a boost controller/ tap for the right price :rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
    • Unfortunately the cavaet to that is that while any scan tool should be able to read the code, the workshop will need a consult plug to OBD socket adapter. You don't have a location on your profile, where are you based?
    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
×
×
  • Create New...