Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Deus Ex Trivia:

During sections of the game where the New York skyline is visible in the background, the two towers of the World Trade Center are noticeably missing; the real towers were destroyed a year after the game was released. Harvey Smith has explained that due to texture memory limitations, the portion of the skyline with the twin towers exists in the game's data files but had to be left out of the final game, with the other half mirrored in place of it. According to Smith, during the game's development, the developers justified the lack of the towers by stating that terrorists had destroyed the World Trade Center earlier in the game's storyline.

Mind. Blown.

Monday on 4 hours sleep no less :(

I'm actually not doing too bad though. Small win.

I had the same but due to unemployment it doesnt matter lol

Morning Mangs,

Considering buying a pair of SSDs... someone talk me out of it

http://en.wikipedia.org/wiki/SSDS

a pair of them? but you drive a 31? surely not necessary

FAT

?

Don't get one.

I remain unconvinced...

http://en.wikipedia.org/wiki/SSDS

a pair of them? but you drive a 31? surely not necessary

I'm a target out there bro

Yeah man, a pair of Super Star Destroyers would rule!

Also: won't be able to make it to ze german club, sorry.... aaand not sure if I'll make it to BR now either. Stupid 34... might need new coil packs.

Edited by GTTG

is dave referring to the FAT hard drive format?

Martin you need SSD's or else there will be no more room on the media harddrives

Yeah man, a pair of Super Star Destroyers would rule!

:thumbsup:

I don't think I have the garage space though :(

Also: won't be able to make it to ze german club, sorry.... aaand not sure if I'll make it to BR now either. Stupid 34... might need new coil packs.

:( :( :(

is dave referring to the FAT hard drive format?

Who uses FAT any more?

Martin you need SSD's or else there will be no more room on the media harddrives

I'll probably buy a 2TB drive for $78 either way...

German club? You guys get moving to german music?

Hells yes, rock the lederhosen and dance to those german beats. Ever been to oktoberfest? :P

Seriously though, its a club but not a night club. You get smashed on awesome german beer and eat awesome german food. Tis good.

Hells yes, rock the lederhosen and dance to those german beats. Ever been to oktoberfest?:P

Seriously though, its a club but not a night club. You get smashed on awesome german beer and eat awesome german food. Tis good.

Ah haha. I was reading some of the past pages... was away for a bit... see its more of a foodie place than 'clubbing' haha.

I been to one in Adelaide, can't remember the name but it is pretty popular place there. Man the salty foods = easy to down beers :D

And ze sausage is leet... as in not 'thats what she said' sausage :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...