Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I've run out of crayon's though.

Nikko pen will be acceptable

Jason you keen for German club?

Suspended in my work = sacked lol.

What time?

sacked,suspended, given the arse and getting a DCM all the same thing.

yer suspended at my work normally means escorted off the premises, they know we have sticky fingers and will take anything even if its bolted down

Although the word mistake at my work can range a fair bit, anywhere from a talk from the manager to a court case for manslaughter

I have a lot of colour pencils. The project manager saw me marking up scaffold drawings in coloured pencil and he was like

PM: Are you marking up drawings in coloured pencils?

Me: Hell yes

PM: You do your planning in coloured pencils?

Me: Hell yes

PM: f**k yeah I love coloured pencils.

I have a lot of colour pencils. The project manager saw me marking up scaffold drawings in coloured pencil and he was like

PM: Are you marking up drawings in coloured pencils?

Me: Hell yes

PM: You do your planning in coloured pencils?

Me: Hell yes

PM: f**k yeah I love coloured pencils.

Lol

and, anybody got an angle grinder I can use, or that can do a slight trim on couple of choice metal bits on my car.

cage is being a real pain in the ass to install

one long pain in the ass

jason i think what you are looking for is called "bailey channel" Im not 100% on this but pretty sure its near enough for someone to know what your talking about

I has angle grinders

you coming to german club tonight, and if so, are you going past your place first?

I just have one support bit where the sunroof used to sit fouling against the cage, so just need to trim it by about 5mm

Had a morning tea this morning to raise funds for the qld flood appeal. Everything that got donated Brookfield is going to match. So far from the head office sites in Brisbane we've raised nearly 13 grand. Solid effort by everyone :cheers:

you coming to german club tonight, and if so, are you going past your place first?

I just have one support bit where the sunroof used to sit fouling against the cage, so just need to trim it by about 5mm

Or, I can swing past your place at some point in the week and you can have a crack, as I haven't used an angle grinder before....

Or, I can swing past your place at some point in the week and you can have a crack, as I haven't used an angle grinder before....

KEEP BODY PARTS AWAY FROM THE SPINNY BIT thumbsup.gif

you coming to german club tonight, and if so, are you going past your place first?

I just have one support bit where the sunroof used to sit fouling against the cage, so just need to trim it by about 5mm

I am, and I am home now. Can bring it if you want. Angle grinder on the train will be baller. Just let me know coz I don't want to bring it if you don't want it.

Or, I can swing past your place at some point in the week and you can have a crack, as I haven't used an angle grinder before....

If you like, although I can take no responsibility for unwanted metal damage...

Had a morning tea this morning to raise funds for the qld flood appeal. Everything that got donated Brookfield is going to match. So far from the head office sites in Brisbane we've raised nearly 13 grand. Solid effort by everyone :cheers:

Awesome stuff. Powerlink is also matching donations dollar for dollar. Was just over 20g this morning.

also keep genitals away from the spinning bit too

Since when are genitals not body parts?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...