Jump to content
SAU Community

Recommended Posts

So ive got my new High-Flow from hypergear and have been advised by many of you guys on these forums to get the injectors and AFM before my tune otherwise ill just have to tune it twice. (Safe tune with standard Inj etc & then retune with new Inj etc)

I have been been reading through Trents (URAS) FAQ on the EMU and it seems as though I can adjust settings fairly easily.

I have all the usual mods and I am running a Greddy EMU, so my question is if I get the software for my EMU and fix the settings for a Z32 AFM can I also redo settings for the Injectors so that I can drive down to CRD for the final tune?

Also if I was planning of playing around with E85 would 750cc Nismos be sufficient??

I am not out to fully tune it myself but I want to save the installation cost of getting CRD to install the Inj's and AFM cause I can do it myself.

Any views would be greatly appreciated.

yes you can change the AFM and injector setting in EMU then drive to CRD for tuning

I would leave the fine tuning of lag times etc to them

as for changing AFM its just in the drop down box on the front page in vehicle settings and injectors are a simple before and after

no in the emanage car setup menu there is a tab called I/J from memory and the first area down the bottom will say 380cc for your before then in the next Box (the after ) you enter the size of your new injectors and the emanage will scale them for you,well good enough to get you to the tuners anyway

www.mohdparts.com

halfway down

you will have to download the full version then update to the latest

also if you havent installed the emanage yet

dont forget to do the jumpers (from memory only jumper no8 needs to be changed )

and you will more then likely need an adapter for inside (the ignition adapter)

Haines

Sorry mate I should have been clear with my original post. EMU is already installed. Was done in early 08 bt CRD, just after the software to have a play on the laptop.

joeyjoejoejunior....(What a mouthfull!) so 750's will be plenty with the "standard mods"? Im currently running 217rwkw before Highflow with standard AFM & Injectors aiming for around 250 odd with the Highflow but maybe a bit more with E85

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...