Jump to content
SAU Community

Recommended Posts

Hi guys and girls!

I have a Metal Cat installed more than 24 months ago. Recently i have been having whitish/grey smoke coming out of my exhaust. Mechanic says it might be some engine oil going into my engine after a session at AHG skidpad(i do not have a oil catch can before was told the reservior on the rocker cover should be sufficient enough). There shouldnt be a problem with the turbo seals as it is a Brand new unit from HKS. The car has been backfiring once in a while.

Whitish/grey smoke was also thought to be condensation but i dont think so cause the car has been driven for more than an hour on the road.

This only happen when i hit full boost! On idle it doenst happen. SO please do help me. I am having tons of problems with the car, all i have done is put good parts and proper mantainance into the car.

SO my question is: Are this the symptoms of a failing CAT?? Does it cause greyish/ whitish smoke to come out of your exhaust?

Link to comment
https://www.sau.com.au/forums/topic/263107-metal-cat/
Share on other sites

Whitish smoke normally due to Condensation in the exhaust but how can this be happening after an hour of driving in a 28 degrees day? Shouldnt all the "water" in the exhaust be gone by now :blink: ?

WHitish smoke can also be cause by engine oil or coolant if i am not mistaken. The tuner and mechanic isnt worried about it because the still reckon its condensation in the exhaust. They have taken the car for a drive and there was another car folowing from behind, all they say was ITS MORE GREY THAN WHITE :D . I am putting all my trust in them as they are one of the most reputable tuner/shop in Perth :D .

The whitish/greyish smoke only blows out when i hit 16psi on most gears!

Link to comment
https://www.sau.com.au/forums/topic/263107-metal-cat/#findComment-4504860
Share on other sites

white smoke on boost means there is a seal that is not working properly - the 3 usual suspects are turbo (water or oil seal), head gasket (oil into the combustion chamber), or leaking from the plenum water galley into the head.

Link to comment
https://www.sau.com.au/forums/topic/263107-metal-cat/#findComment-4504915
Share on other sites

Whitish smoke normally due to Condensation in the exhaust but how can this be happening after an hour of driving in a 28 degrees day? Shouldnt all the "water" in the exhaust be gone by now :( ?

Correct - its not water/condensation. That will all boil off even before you cars fully up to temp.

WHitish smoke can also be cause by engine oil or coolant if i am not mistaken. The tuner and mechanic isnt worried about it because the still reckon its condensation in the exhaust. They have taken the car for a drive and there was another car folowing from behind, all they say was ITS MORE GREY THAN WHITE :ermm: . I am putting all my trust in them as they are one of the most reputable tuner/shop in Perth :happy: .

The whitish/greyish smoke only blows out when i hit 16psi on most gears!

My guess is oil - what does the dipstick say?

Dead cat = black smoke.

Link to comment
https://www.sau.com.au/forums/topic/263107-metal-cat/#findComment-4505170
Share on other sites

i just re-read my post. its usually water in the combustion chamber that causes white smoke. burnt oil is usually blue.

What causes the water to go into the combustion chamber??

And why doesnt the whitish/greyish smoke comes out during idling. If theres water shouldnt there be constant smoke coming out :O ?? DOenst the water recirculated when it is idling?

The oil level was check regularly, it seems fine.... and the oil pressure on the dash all seems normal.

Just came back from a drive, got my missus to drive it while i follow her around.

The smoke smells more like something is burning.... Smells like weed :D .... Nah just joking. IT smells like something is burning. Doesnt smell like running too rich (petrol smell)

Link to comment
https://www.sau.com.au/forums/topic/263107-metal-cat/#findComment-4505647
Share on other sites

What causes the water to go into the combustion chamber??

And why doesnt the whitish/greyish smoke comes out during idling. If theres water shouldnt there be constant smoke coming out ;) ?? DOenst the water recirculated when it is idling?

The oil level was check regularly, it seems fine.... and the oil pressure on the dash all seems normal.

Just came back from a drive, got my missus to drive it while i follow her around.

The smoke smells more like something is burning.... Smells like weed :( .... Nah just joking. IT smells like something is burning. Doesnt smell like running too rich (petrol smell)

i covered that.

white smoke on boost means there is a seal that is not working properly - the 3 usual suspects are turbo (water or oil seal), head gasket (oil into the combustion chamber), or leaking from the plenum water galley into the head.

from what i can gather it sounds like you're smelling burnt oil. find out where its coming from. check the following:

- the lowest point on the hot side of your cooler piping,

- radiator for milky residue under the cap and

- your intake pipe.

if it is actually oil then there will be traces there. if not then at least we can rule that out.

Link to comment
https://www.sau.com.au/forums/topic/263107-metal-cat/#findComment-4512821
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...