Jump to content
SAU Community

Recommended Posts

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

MY32 pm'ed you re skirts and pods.

GTR94 will get back to you re boot/fuel door release cable ( got to look for it, it may have sold with other stuff)

I got a wharehouse full of car bits!!)

Edited by dat2kman
yo man cant reply to your pm aye cause i havnt got enough post counts. would you let it go for 220? if so then i'll pick it up tomoro or sunday at the latest

Pmed you.

$50 price drop is pretty fair if you buy the lot

can do better on $$$ if there is more stuff you are after

hey mate do u have any pics of the rb26dett??

cheers jack

Why?

All you can see is the top of a motor?

Speedo shows 77000 kms, it has aftermarket pod filters, that about it.

We can show you a vid of it running, and no I CBF putting it on youtube.

It's a front section off a car, with a nissan engine and other shizz stuck in there as it came from the manufacturer.

Come and take some pics yourself if you like

hey mate just wondering if you got it and how much for the boot cable posted to Victoria. just after the cable that actually opens the boot. cheers

Got it, pm'ed you, it will come with the push/pull handle as well

has the engine been pressure tested? and is it just a standard motor?

Stock motor hasn't been pulled apart, done 77000kms, history is known to the one australian owner

was comp tested when last run reading were all even ( no variances)

hey mate, do you have reverse sensor switch?

That is still attached to the gearbox which will go with the front cut.

Sorry

hey mate was wondering do u have a 32 front crossmember...

if so would u deliver i am in north brisbane... po 4017

cheers roger

Sorry cant help you, looks like the front cut may be sold to a member in Adelaide, we are working out freight arrangements ATM, and the X member is part of the front cut.

  • 2 weeks later...
hey mate do you still have the gtr grill , are all the clips still there . what about a complete battery clamp?

sorry grill sold, & no battery clamp/brackets.

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...