Jump to content
SAU Community

Bee - R Limiter


Recommended Posts

  • 2 weeks later...
whats the advantage of these over the stock rev limiter?

the way in which it works differs from the factory rev limiter in that it is an ignition cut, as opposed to a fuel cut. The reason for this is because if an engine (particularly turbocharged) regularly hits a fuel-cut rev limit (such as in high performance driving, or particularly drifting) engine damage can arise due to the lean condition produced when the original ECU shuts off the fuel pump.

The BEE*R rev-limiter allows fuel to pass into the engine still, limiting engine speed by disabling the ignition signal. The Bee*R rev limiter is fully adjustable in 500rpm increments, for safety reasons allowing only a lower rev-limit to be configured than standard. If you have spent a lot of money tuning your engine, or are running at high RPM’s for extended periods of time, it could be recommended to run a lower rev-limit to prolong engine life. Both Formula 1 and JGTC cars use ignition cutting rev limiters, so it is a fully race proven concept.

The Bee*R can also be used as a “two stage rev limiter”, as an aid for launching your car. The Bee*R is configurable for two different rev-limits. A lower rev limit can be activated by a switch, the handbrake switch often being used. This configurable lower limit, can be set to the optimum RPM to launch your particular car from in 500rpm increments. When the handbrake is released, the usual rev limit comes into action, allowing quick launches, and full performance down the strip.

Link to comment
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • A million years later, searching for something else I posted, I was reminded of this thread. I eventually bought a new gauge. Put it in using the same probe (which has been installed the whole time stopping the exhaust gas from coming out the hole) and.... normal service has been resumed. The old gauge was definitely broken. /semi-pointless closure.
    • They're available from Nissan! I was able to buy a GTR (R33) one.. relatively* recently. Perhaps this stopped now but I bought mine ... relatively recently. I believe the 300ZX one has a different knee-point which is more rear biased, which I think the HFM one echos.
    • Hey Team, A bit to unload here. Hello from New Zealand I have a 2009 Nissan Skyline 370GT ( Type SP ) Auto 7 Speed, that I've had since 2022 and have loved the car since. Its painted in its factory QAB ( White Pearl ) with the Impul front lip and rare boot lid/spoiler with woodgrain interior. Mods since I've bought it and installed: Stillen Gen 3 Long Tube Intakes Motordyne Shockwave Catback Exhaust JDM Skyline Taillights Fake carbon spoiler and front grill ( Will be taking off.... its cringe ) VR30DETT Transmission from the Q50/Q60 to hold up to 550 Foot pounds of Torque ( 753 nm ) reliable  Currently I plan to turbo the car and have all the parts needed ( Photo Included ), I have my tuning day set on August 8th and choosing EcuTek as my tuning platform. Two of my work colleagues has their 370Z ( Manuel ) and 370GT coupe ( Type SP - Manuel ) also turbo'd and they have inspired me to get it done I have prepped quite a wee bit for this, as I had done the VR30 transmission swap over to this car so that I can achieve my HP goals without torque being an issue. I've taken quite a cautions route, as im always thinking about the safety as well as performance with my build, I'd rather do it properly and not cut corners etc etc. Any who, I've recently picked up the AutoStrada cruise control kit with all the included cables/wires/instructions. I've been hella researching around and can't find much on the integration that it has with the ECU and/or system. the only reason why im asking is, because I'm getting EcuTek and one of them RaceRom features allows the ability to switch maps via the cruise control function, which I am currently in the grey area if this would add-on via the Canbus will allow me to switch maps or have the option to use Cruise Control to begin with ( showing up on the instrument cluster to advise Cruise Control being set etc etc )  Because of my model being Type SP, Cruise Control on these models was never an option from factory unfortunately.  Anyone here that is able to shed some light on if the Cruise Control via AutoStrada gives OEM ability over the cruise control. Would love and appreciate any response and/or assistance with this, also happy to answer any question about my build and ill try pitch in where I can. Warm Regards,  
    • I thought the only (new) BM57 that was readily available was the one that was a BM57 but with the wrong bias. HFM or someone's?
×
×
  • Create New...