Jump to content
SAU Community

Recommended Posts

Some questions about this.

It's an amplifier, but it's accepting an amplified signal already, ie the speaker output from your headunit which will typically be 22W RMS, however the rear speakers are only rated for 8W RMS. I haven't looked at the front ones.

Does it just drive the rear speakers or does it drive the front ones too. If it's just driving the rears then is it perhaps a high pass filter and the rears are just tweeters with the fronts being full range?

If it is actually an amplifier and drives all 4 speakers is there any way to trick it into accepting a line-level input as this will allow me to simplify my Car PC install dramatically as I'll just need to glue my USB soundcard to the amplifier and make up some leads rather than do a full amp+speakers installation.

the box is the rear amp it drives only the rear speakers i removed mine and spliced and soldered the wires together because it stuffed up and i wasnt getting a signal to my rear speakers any more its useless most decks perform better than 80's junk any how

  • 3 weeks later...

ok... so i removed 2 boxes today... (car did have hicas / abs etc..)

are they both amplifiers?????

one is a small one about 8cm x 3cm taken from under parcel shelf on drivers side moreso

the other is about A5 size... taken from just off centre moreso toward passender side from under parcel shelf.

they both for stereo???????????????

ta

  • 3 weeks later...

i have 3 unidentified boxes lol,,,

huge on on the passenger side bigger than computer silver with 2 looks

another in the middle ( the amp i think )

and 1 on drivers side much smaller with just 1 loom to it ?

anyone know what these are yet ?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...