Jump to content
SAU Community

Suspension Soft & Bouncy After Motor Change

boostdef
 Share

Recommended Posts

boostdef Enthusiast

boostdef

Posted
Posted

Hi,

Can anyone tell me whats going on? I have just changed the motor in an R33 gtst which has khoni adjustables at the front, and the from suspension is extremely soft and bounces like a boat in waves as im driving along.

I did not touch the suspension at all, just a simple jack the car up, change the motor and put it back down?? wtf?

Any help would be greatly appreciated :blink:

nisskid Grand Master

nisskid

Posted
Posted

sway bars still connected properly? dont think u need to take them off to change the engine, but it does go near to the sump so its possible. also did u have a strut brace on before? not usually a noticeable "handling" difference, mostly a mid-corner grip thing.

also was it a straight engine swap? u didnt put a heavier engine in did u?

boostdef Enthusiast

boostdef

Posted
  • Author
Posted
sway bars still connected properly? dont think u need to take them off to change the engine, but it does go near to the sump so its possible. also did u have a strut brace on before? not usually a noticeable "handling" difference, mostly a mid-corner grip thing.

also was it a straight engine swap? u didnt put a heavier engine in did u?

Straight engine swap by replacing a S1 motor with a S2 motor.I dont recall at all undoing any sway bars. Was pretty much engine mounts, bellhousing bolts and the little things here and there and that was it.The shocks i think are khoni adjustables with a bolt at the top, and i think a something to adjust underneath.Its just like they are now ultra soft and i go over 1 bump and the front goes up and down constantly for about 10 seconds. Plus, it is bottoming out a lot more obviously due to the softness :(Can I simply adjust them at all? Is it the top bolt i adjust or underneath? (Sorry new to this)

boostdef Enthusiast

boostdef

Posted
  • Author
Posted
Didnt drop the engine in to hard and bust the seals in the shocks did you?

Naa it all seemed smooth as! Dropped it in extremely carefully. But I suppose thats a possibility I may have done something.Another thing I forgot to mention is they are Coilover types i think. Ones with the adjuster at the bottom of the spring and the bolt at the top. Can it simply be a case of stiffening the spring? (Not that it explains what the go is though :P)

nisskid Grand Master

nisskid

Posted
Posted
Straight engine swap by replacing a S1 motor with a S2 motor.I dont recall at all undoing any sway bars. Was pretty much engine mounts, bellhousing bolts and the little things here and there and that was it.The shocks i think are khoni adjustables with a bolt at the top, and i think a something to adjust underneath.Its just like they are now ultra soft and i go over 1 bump and the front goes up and down constantly for about 10 seconds. Plus, it is bottoming out a lot more obviously due to the softness :(Can I simply adjust them at all? Is it the top bolt i adjust or underneath? (Sorry new to this)

sounds like ur shocks are buggered for some reason, are they on full hard adjustment wise?

boostdef Enthusiast

boostdef

Posted
  • Author
Posted
sounds like ur shocks are buggered for some reason, are they on full hard adjustment wise?

The bottom coil adjustment is about half/half, and the top bolt is just on the thread (ie the shaft of the shocks are just above the top of the bolt.

Would having the wheels in the air for an extended time do this? Because thats the only thing I can think of really.

petern Enthusiast

petern

Posted
Posted (edited)

i think you just answered your own question in that last sentence......

having the the wheels in the air for an extended period would put pressure on the shocks - weight of the wheels and brakes.

I know when I disconnect the shocks on the rear on my 1600, i can push down on the back and bounces a fair bit.

I would say shocks are stuffed!

Edited by petern
nisskid Grand Master

nisskid

Posted
Posted

wheels in the air shouldnt bust ur shocks, as they are still in the static position, but will put a bit of pressure on the travel stops if it is infact the shocks which are suspending the wheel, often its the arms/rods or half shaft suspending the wheels up, and the shocks arent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      Hi everyone.

      By Marek · Posted

      Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • DanMac34
      R34 Speedo not working after manual swap

      By DanMac34 · Posted

      Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • joshuaho96
      Speed Sensor replacement

      By joshuaho96 · Posted

      Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...