Jump to content
SAU Community

Recommended Posts

befor u go and pay $500-$600 for coilpacks, get some heat temp proof silicone and fill in the gaps on your coilpacks so it cant earth out on head instead of on plug. Search coilpack budget mods, you might find pictures.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4543001
Share on other sites

Hey everyone!!

My brothers R34Gt-t is misfiring when ever you put the foot down a bit. Its fine when hes driving soft, but misfires bad when he tries to go hard. We've already changed the spark plugs and think now that it may be the coilpacks???

Any ideas???

(i did search but didn't find much...)

Thanks

Hi MATthere is lot`s on this may be you didn`t have much Searchluck it is hard some time`s :thumbsup: ,better luck next time,cheer`s chuckie .
Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4543654
Share on other sites

What gap are the new plugs he's using? and what boost is being run?

The issue sounds like coil packs (very common at higher boost levels) but the problem often can be reduced or eliminated by using plugs with a smaller 0.8mm gap (or less depending on boost) as opposed to the std 1.1mm gap.

This worked for me and the insulation of the coil packs didn't, I still have a slight miss and are currently waiting for JJR coils to be back in stock for the R33 S2.

Also Splitfires are great but they are $600+, Super Sparks can be had for $500, JJR have coil packs for $400 (1yr warranty) that do the same job and there are some Yellow Jackets just come on the market for $350 a set (6 month warranty). For my money I'm going for the JJRs - same warranty and result as Splitfires.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4553483
Share on other sites

does it hesitate coming onto boost? i had a similar issue, also had a dodgy idle, turned out to just be a vac leak. pulled out my coils and they looked brand new!! so just be sure to check everything before spending a few hundred on coils :)

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4554183
Share on other sites

  • 2 weeks later...
What gap are the new plugs he's using? and what boost is being run?

The issue sounds like coil packs (very common at higher boost levels) but the problem often can be reduced or eliminated by using plugs with a smaller 0.8mm gap (or less depending on boost) as opposed to the std 1.1mm gap.

This worked for me and the insulation of the coil packs didn't, I still have a slight miss and are currently waiting for JJR coils to be back in stock for the R33 S2.

Also Splitfires are great but they are $600+, Super Sparks can be had for $500, JJR have coil packs for $400 (1yr warranty) that do the same job and there are some Yellow Jackets just come on the market for $350 a set (6 month warranty). For my money I'm going for the JJRs - same warranty and result as Splitfires.

Ive had a set of yellow jackets in my GTST for around 3 months now and they have never missed a beat. They actually come with a 12 month warranty too. Theres a group buy for them here on SAU and they are only $320. So cheaper than JJR, same results as Splitfire and same waranty.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4578373
Share on other sites

Try coating the coils as already mentioned and see how that works.

Splitfires aren't worth the money unless you aren't very mechanically inclined and/or you want a COP setup like stock. I am in the process of swapping my old coils since the epoxy didn't help in the high rpms. I picked up a set of 8 Chevy Corvette LS2 coils for $125USD and mounted them along the firewall with separate spark plug wires. They should blast the splitfires away and provide adequate spark for whatever I throw at them. Plus they have built in ignitors so I can get rid of my RB25 Series 1 ignitor/power transistor unit (PTU) and wire them directly from the ECU.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4578870
Share on other sites

Only problem i'v ever had with coils is when one died. Not sure any of the aftermarket ones can offer a much if any greater spark unless you introduce leads in to the equation like above...

before anything, like said before, clean out around the spark plug hole and clean the sleeves then spray it all with silicon spray and i can't see why unless a jacket is damaged you would have problems given that there is not a fault in the coil or wiring itself...

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4579042
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...