Jump to content
SAU Community

Recommended Posts

Hey Guys,

I've done a search, but couldn't find anything. I know it's probably been asked before, if so just point me at the right place. Anyhoo, i was thinking of taking my car down to the wakie day (sounds awsome :D ), but i'm concerned that my rather stock car may break :woot: lol

mods are only: 3" full exhaust, r34 smic, high boost solenoid mod, and some rims.

My main points of concern are:

1. The guys that put my rims on also put some spacers. Not sure how serious this is, but it's in the back of my mind

2. My brakes. My rotors definitely need machining, as i can feel some shudder on hard deceleration. I would get that done beforehand, but will the stock breaks handle the intense work-out?

So my main question is has anyone taken a stock skyline to the track, and was it able to handle it?

I'm not expecting it to break any records, just want to make sure the car will be up to it.

Thanks in advance :D

Link to comment
https://www.sau.com.au/forums/topic/266325-tracking-a-stock-ish-skyline/
Share on other sites

Stock r33 GTST's actually have proved themselves very reliable at wakefield.

Bleed the brakes, make sure its got a lot of oil in it, dont bother washing it, then come have fun.

The brakes will have more wear than on the street (well, duh), but nothing to worry about as long as there's enough pad material left and the rotors arent too thin :woot:

lol what tyre place puts on spacers to fit wheels for u?

anyway, id check that.

but yeh, fluids and pads need to be checked, if ur pads have heaps of meat left just leave them and watch out for fade, but as far as fluid goes get something decent as fluid can boil and go without warning.

Marcus I ran my very stock gtst at a heap of track days for years and had almost no problems. Like yours it needed new discs/discs machined after every couple of track days, and as said above you should have new oil, properly bled brakes and a wheel alignment.

Just get a good workshop to check the car over and make sure everything is OK (they are getting old, it might need bushes replaced or similar), and get rid of the wheel spacers unless they are absolutely necessary.

Nissan built an amazingly capable car from the factory, don't be concerned about giving it a bit.....they love it.

MUST DO: Flush your brake system with a decent brake fluid like Motul RBF600 (I think thats the number). You WILL get brake fade after a few laps with just regular fluid.

Its more important than anything else, cause when youre coming into a corner and theres no brakes, fresh oil and a wheel alignment wont stop you from hitting a wall :woot:

Thanks for the replies guys. I'll get the brakes done this week - I've got some QFM pads ready to go on once the discs are machined. While they're there I can get them to bleed the brakes for me ;)

Now just the spacers to worry about... i had to go and get dished rims didn't I :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...