Jump to content
SAU Community

Speed Sensitive Steering - What Controls It?

bubba
 Share

Recommended Posts

bubba Grand Master

bubba

Posted
Posted

Trying to figure out what controls the speed sensitive steering in my R32 for a couple of reasons..

First being that I would like to turn it off for track days (could just pull the plug from the HICAS computer I guess).

Secondly, I would like my Stagea to have the same sort of speed sensitive steering.. definitely needs to be heavier at high speed.

Is it purely electronically controlled? or is there special valving or something involved?

/discuss

some_cs_student Veteran

some_cs_student

Posted
Posted

Pretty sure its the HICAS computer, check the tutorial on removing hicas, it mentions not disconnecting the ECU for a reason on an R33, I *think* its the same for an R32 but best to check...

predator Grand Master

predator

Posted
Posted

On r32 for speed sentivity - valve .. controlled by ECU, based on speedo.

Disconnecting the plug is not going to do much, other than let the toe in of the rear wheels vibrate around which will not give you any benefit. To do it properly you need to lock the rack.

Rear swaybar and locked rack makes a good difference - very predictable.

bubba Grand Master

bubba

Posted
  • Author
Posted

Where is that valve located? pump or rack? would there be a way to set this up in the Stagea?

Already got a lockbar along with swaybars and coilovers etc in the 32, HICAS computer is still plugged in. Would pulling the plug on the HICAS computer immediately turn the steering hard? I guess if it's controlled by the HICAS computer and that is removed then it should instantly become heavy..

nisskid Grand Master

nisskid

Posted
Posted

what do u mean take it out for track, u mean the HICAS or the speed sensitive front steering?

there is a speed sensitive control, pretty sure it works off the speedo cable, im pretty sure there are 2 stages, full power steering, and just power assist. personally i think any proper circuit work feels like shit with only power assist, having only power assist for highway driving is good as not much turning is needed, so the wheel is firm and doesnt want to move a lot, but when ur trying to move it a lot like at the track it feels like shit.

a manual rack is one thing, a powered rack without powersteering is another, atm i have an issue where i can only get power assist at all speeds (due to not having a speedo) and especially for drift it feels like shit, yes its harder to turn, but not in a good way, the rack is very sluggish unlike a manual rack, it provides fark all feedback and just doesnt feel very responsive at all.

this probably has nothing to do with what ur talking about, but yeh.

bubba Grand Master

bubba

Posted
  • Author
Posted

I'm talking about the speed sensitive steering for the front..

My understanding was that it is progressive from ~60km/h - ~100km/h.

Anyway, the MAIN reason for this topic, is to try to understand what controls the speed sensitive steering and whether it could be adapted to another car..

heller44 Mentor

heller44

Posted
Posted (edited)

Basically, on a 32 anyways, you have the mechanical speedo drive to the dash cluster. Then from the cluster you get a pulsed output relative to speed (frequency changes not duty cycle) that is transmitted to the hicas / ps module in the boot. This then works out what is meant to happen and outputs a signal to the solenoid on the power steering rack (front of car) that changes the hydraulic assist effort. This signal is fixed frequency but varying duty cycle.

I understand with 33 and 34's it is the same, just no hicas hydraulics, but power steer assis is still hydraulic solenoid, same same.

To transfer the lot into another vehicle you would need some sort of module to replicate this completely and having a speed input available, using a hicas ecu wouldn't work cos it will fault with not seeing the the correct responses from the hicas, wheel sensors, steering wheel angle sensor. As well as using a rack with the solenoid on it.

I have thought about making a unit up to remove the hicas ecu and just do the steering assist but haven't been arsed yet. Got my hicas / power steering all working before I made it that far.

If any of that made sense, well..

:/

James.

*edit ps, definately progressive, I have a graph here from the gtr workshop manual, and a couple of cro photos from when I was discussing this with SK a long time ago..

Edited by heller44
bubba Grand Master

bubba

Posted
  • Author
Posted
my stag felt a little better once i added adjustable camber/castor bushes and wound in max castor

My stag handles really well, it's just the steering at high speed is too light for my liking..

Heller, cheers :) I was thinking something like a variable resistor on the wire going to the rack solenoid but now that you say it's varying frequencies that controls would probably need something like a pulse width modulator? (I'm not an electronics guy :))

heller44 Mentor

heller44

Posted
Posted

Does the stag have variable assist at all?

One thing you could do for track use with the 32 is shove a switch in line with the rack solenoid, open the circuit. My car was like this for over a year cos the git that wired everything up forgot to wire the rack in, along with the clutch switch, reverse light, speed signal, etc etc... :) was quite driveable, even carpark speeds weren't a problem, if you climb under the car, and look from the back of the rack forward, you will see the solenoid where the steering column mates up. Just unplug it there and test..

The unit I was thinking of making would just take a speed input and generate the solenoid drive.. Letting you lock out the hicas without a fault and being able to adjust the gain of the steering to how you wanted it.. Reasonably simple circuitry just haven't found time effort motivation..

260DET Experienced

260DET

Posted
Posted

Interesting topic, does the solenoid operate a variable volume valve to regulate the amount of oil flow? In other words, what mechanical device regulates the amount of power steering? And in what way does the solenoid operate that mechanical device?

bubba Grand Master

bubba

Posted
  • Author
Posted
Does the stag have variable assist at all?

One thing you could do for track use with the 32 is shove a switch in line with the rack solenoid, open the circuit. My car was like this for over a year cos the git that wired everything up forgot to wire the rack in, along with the clutch switch, reverse light, speed signal, etc etc... :P was quite driveable, even carpark speeds weren't a problem, if you climb under the car, and look from the back of the rack forward, you will see the solenoid where the steering column mates up. Just unplug it there and test..

The unit I was thinking of making would just take a speed input and generate the solenoid drive.. Letting you lock out the hicas without a fault and being able to adjust the gain of the steering to how you wanted it.. Reasonably simple circuitry just haven't found time effort motivation..

Is the solenoid you are referring to the big HICAS solenoid thing under the intake manifold? if so, I removed that when I removed all of the associated HICAS gadgetry. All that is left is the HICAS computer in the boot..

I like your thinking with the circuitry, I'm not sure if the Stagea has variable assist but even if it didn't, could a signal be intercepted or modified at all?

heller44 Mentor

heller44

Posted
Posted

The solenoid is built into the steering rack itself, where the steering column meets the horizontal part of the rack the solenoid is like a large wart on the intersection, two wires coming out of it to a two pin inline connector to a harness that dissapears up into the nethers of the car.. You might be able to see easier than me, the 26 and its attendant bits fills the engine bay that well my monkey mitts can't follow..

If there is no solenoid on the stag, you would have to insert something like a bypass valve in the hydraulic loop to reduce the assist. Not something I would be playing with. Have a look and see, I would be suprised if it doesn't have it since it is basically a 'line anyway.

One way to alter the solenoid drive signal is to use something like the jaycar kit, digital pulse adjuster.. takes a duty cycle input and modifies it for the output.. Seem to remember an autospeed artical using this kit for adjusting the steering response on a lexus or something a while back.

James.

bubba Grand Master

bubba

Posted
  • Author
Posted

Excellent work James, I will report back when I have investigated a little further!

Engine is coming out of the 32 soon so will look at the rack and splice in a switch. Will also attempt to look at the rack in the Stag.. not sure if I'll be able to see anything past the diff/driveshaft/etc.

heller44 Mentor

heller44

Posted
Posted

Put the car up on ramps, slide in under the drivers side floorpan and look forward at the rack. It is very obvious what you are looking at when you get there.

Try unplugging the solenoid before you go to the trouble of a switch.. You might not like it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX 路 Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • Duncan
      Duncan's V37.......race car?

      By Duncan 路 Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan 路 Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan 路 Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan 路 Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
脳
脳
  • Create New...