Jump to content
SAU Community

Omp Harness, Rb26 Feul Rail And 6boost, Chev Rods, New Gt3076, S13 Axles

Recommended Posts

Following for sale :

GT3076R BRAND NEW turbo. External gate T3 0.63 rear. $1400

S13 5 bolt axles, knuckles and rear stock brakes. Left / right pair $60

OMP 4 point Harness, Italian made. Hardly used. Comes with bolt in eyes and will bolt into most any car using standard points(rear seat). Selling as had to go to 5 point - $150

RB26 6boost manifold, brand new un-used. T4 split perfect for T04z on RB26. $1000

RB26 aftermarket fuel rail has dash ends. $80

Also have 6 x NEW ally chev rods(I assume 350) where for a rb30 but went another way. I think they are Eagle - $180

Pics of the fuel rail -> http://butters.throwinghandles.com/file_st...B26FuelRail.jpg

Pic of the Turbo




In Perth WA, happy to ship/post at buyers expense.

Usual story first to door gets item. PM / POST of "I will take that" guarentees nothing.

Link to comment
Share on other sites

  • 2 weeks later...

Sorry guys didn't relise the thread had been replied to. My auto email notify was off :starwars:

GTRDJ - aplogies too just saw your PM but Fuel rail is sold.

Ok everything is sold except the OMP harness.

Pretty sure the harness is FIA, will post up along with a picture of the tag.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Posts

    • And lower chances of a divorce, hookers & coke much higher chance, a bit lower are strippers & coke.
    • Been slowly chipping away at it when I've got time. Tried to get the box in with the converter but worked out that the flexplate isn't the correct thickness and the converter pulls out off the pump too much (about 8mm). The flexplate for some reason was setup to use the secondary holes on the converter which had a press in nut to bolt to. I worked with Adamat performance the guys who manufacture the kits and they revised the design and made it suit the factory converter holes and milled up a new one for me and is currently on its way over. Can see the differences between the two compared to the orignal design which is in the post above. Once that's here the box can go in for good. I dummy'd it back up to get tailshaft length and is currently with Hardy Spicer to sort that out. Unfortunately won't get it back until late Jan Have been working in the boot lately getting it all a bit nicer and useable. Painted it with sound deadener and cut out a new boot floor from 18mm MDF so I can put a pram or my tool bag in the back. Have marine carpet coming to stick onto that and then also cut a piece to cover the battery. Once ive stuck the carpet in and all cleaned up ill pop the fuel system back in. Need to order 2 new Walbro 525s to replace the 3x 460s. Should be enough fuel for the new setup and run a bit cooler as well having more volume in the surge tank and less heat.  Have also ordered some sound deadener to put under the carpet. That should be here next week and I'll start putting it down on the floor, doors and roof. Hoping all this effort will make it a nice streeter with ability to daily if I want to.
    • It's only money. This arrived for mine yesterday 
    • Unfortunately my car was stolen in the last few weeks while I was away. Car towed from garage in brisbane south. Wasn’t running and unregistered but good condition white 1994 series 1 r33 gts-t. Black 17inch kakimoto rims, fujitsubo ti exhaust, gtr drivers seat, hybrid fmic, standard body with m spec front bar.  reward for information that leads to recovery.    thanks
  • Create New...