Jump to content
SAU Community

Recommended Posts

I've got my mines chipped ECU for sale which i used in my AUTO - this will suit both manual and auto series 1 r33's, im not sure if it works on series 2.

Specs are:

- Removed rev limiter

- Richer maps to handle hiflow turbo + breathing mods + ~15psi boost. AFR's were at 11.8-12 on boost and ~15.1 AFR cruising.

- Annoying boost cut/r&r removed. I'd log a 5.1v @ 4500rpm and it wouldnt even hesitate to rev.

- would give me 460km to the tank +/-30km depending on how i drove.

Im after $300 + post. by far the BEST bang for your buck mod - you'll notice the power difference instantly even on a standard setup.

I can be contacted via PM or post here.

Pics will be up soon.

Cheers,

Joe

Link to comment
https://www.sau.com.au/forums/topic/267051-mines-ecu-for-r33-gtst/
Share on other sites

not sure on an actual figure mate but i would estimate around 210-215kw when i was running around 10psi, i cant comment on 15psi as i wasnt getting traction at all but it felt awesome. believe me, if you had this in your car you would be confused as to why these things are going for so cheap!

not sure on an actual figure mate but i would estimate around 210-215kw when i was running around 10psi, i cant comment on 15psi as i wasnt getting traction at all but it felt awesome. believe me, if you had this in your car you would be confused as to why these things are going for so cheap!

Yeah mine has 201kw with standard ecu and injectors on 13psi, did yours have bigger injectors with the mines ecu?

And wats the go if u wanna go run 18psi with this ecu, is there much stuffing around?

where ur location?

sydney west

Yeah mine has 201kw with standard ecu and injectors on 13psi, did yours have bigger injectors with the mines ecu?

And wats the go if u wanna go run 18psi with this ecu, is there much stuffing around?

nah mate it had standard injectors. to boost it up to 18psi you wont need much work - just turn up the boost lol.

either way i wouldnt do more than what i said in my first post without getting on a dyno and checking that your AFR's are ok.

im interested. Is it good @ fuel and air flow tuning?

read my first post mate, all the info is there. its not a tuneable computer hence the reason why its so cheap. you just plug it in and off you go.

if you wanted to tune it you'd strap a emanage blue or ultimate to it and you'll be sweet. it will still cost you less than getting a full aftermarket computer if you wanted to go bigger injectors etc etc later on.

I've got my mines chipped ECU for sale which i used in my AUTO - this will suit both manual and auto series 1 r33's, im not sure if it works on series 2.

Specs are:

- Removed rev limiter

- Richer maps to handle hiflow turbo + breathing mods + ~15psi boost. AFR's were at 11.8-12 on boost and ~15.1 AFR cruising.

- Annoying boost cut/r&r removed. I'd log a 5.1v @ 4500rpm and it wouldnt even hesitate to rev.

- would give me 460km to the tank +/-30km depending on how i drove.

Im after $300 + post. by far the BEST bang for your buck mod - you'll notice the power difference instantly even on a standard setup.

I can be contacted via PM or post here.

Pics will be up soon.

Cheers,

Joe

Is it still for sale?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...