Jump to content
SAU Community

Recommended Posts

Hi,

Got a bit of a prob, rear passanger side bearing disintegrated, with it the seal, and apparently there's a spacer that goes b/w the bearing and the cover that holds the whole thing together

Can someone supply me with a diagram of how this thing is meant to be put together?

BTW, I'm in PNG, so going down to the wreckers is not an option

Cheers

KB

Link to comment
https://www.sau.com.au/forums/topic/267443-need-88-skyline-diffbearing-diagram/
Share on other sites

In that case it's probably a local R31 with a live axle.

I guess the bearing your talking about is out on the end near the wheel eh!

If this is the case, the bearing you're talking about is just behind the axle mount flange. Correct?????

Cheers, D

And remember, it's a retainer, ie it retains the bearing on the shaft. More importantly, it retains the whole axle in the housing, preventing it (and your wheel) parting company with the car. Don't just bash the retainer on with a hammer. I'm inclined to think that if you need to ask questions on an internet forum, you probably should get someone more experienced to fit the bearings for you.

  • 2 weeks later...

yea if aus r31 will b bw78 diff. will need 2 drop ur centre out and press off the old bearing. then just go 2 a bearing joint and match it up (dunno what auto places u have there?). just normal taper roller/plain bearing or something (cnt remember) nothing special. press new 1 back on and this ring ur talkin about is ur shim, it sets the backlash between the pinion and crown gear. goes between the bearing and diff housing will def need it.

should b pretty straight forward taking it out when looking at it.

take wheels off, slide disks off (floating rear), undo 4 bolt axle flanges, pull axles out, undo diff plate, undo 4 bolts on the bearing cups. then diff centre should just fall out, might have 2 jimmy it out with large screw driver etc...

close-ish just dw about the mini spool part. more stuff on that site\/

http://wiki.r31skylineclub.com/index.php?t...ng_a_Mini_Spool

Edited by OUTATIME

We've got the bearing out, that's not a prob, but my mechanic recons there should have been a spacer holding the bearing in place. and we need the part numbers for the spacer/retainer and the seal

The old bearing was in bits and pieces when we took the cover and axel out...

N

:):D What is it about people posting tech how-to articles and them filling them with crappy mobile phone photos? Even the most basic phone takes half decent pics now, and digi cameras aren't that dear (my son's $70 job takes fantastic photos). Sorry for the rant but I take tech photos and write tech reports for a living and this kind of thing just sh!ts me no end.

Now that's out of my system, I have a Nissan Service Manual, and there are no pics in there showing the rear axle installation. It does, however mention the bearing retainer ring which goes on the inboard side of the bearing. Note this ring is never to be reused, and a new one will be supplied with the bearing kit. Your mechanic is correct - there should have been one. don't fret if you can't find it, as a new one will be supplied (as long as it's not floaring in your axle housing somewhere :banana: )

The photo below shows a Mazda RX2 setup, which uses the same concept as all live axle setups AFAIK. note that the locking collar has been welded to the axle in the photo - not what I'd call good practice, but it's how I got the car. Apparently it was a common fix for early Falcon (c1970's) when the rear axles used to pull out whilst driving.

post-266-1242276165_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...