Jump to content
SAU Community

Recommended Posts

3yrs old

18,000kms

needs oil line and requires an actuator

bolts onto standard water lines

checked over by Bill at ATS (marion rd, adelaide) and said to be in top notch condition

seals are said to be all good same goes for bearings and shaft play is near non existent

great for an RB20

good on an RB25

$500 pickup

$550 delivered Australia-wide

at4.jpg

at3.jpg

at1.jpg

at2.jpg

at5.jpg

Link to comment
https://www.sau.com.au/forums/topic/268031-used-slide-turbo/
Share on other sites

was on Stagea rb25 auto, stock injectors, safc/sitc/fmic/040 fuel pump/exhaust got 206rwkw

sliding performance listed these turbos at 250rwkw @ 1.1bar

definately no lag, was same as stock turbo but a hell of a lot more punch, and sounds pretty whooshy too

made a huge difference to the engine, this turbo is how the stock nissans should have been made.

stock water lines should be a M24 bolt so yes they will fit

oil line is a M17 bolt and I made a braided unit.

the stock one will fit BUT you'd have to derestrict the oil line slightly with a .8mm drill bit as this turbo needs more oil than the stock turbo

for sale is the turbo only, no lines no other bits. bolts onto rb20/25.

search around this site "sliding performance highflow turbo 2006" for pictures on the oil line modification

with manual gearbox, bigger injectors, power-fc & support mods Id say the turbo should pull 230-240rwkw

cheers

great for an RB20

good on an RB25

Will be pretty damn great on a 25 too!

Wont be that laggy on a 20 and wont be laggy at all on a 25 and should be good for approx 250rwkw.

Would buy this for sure if i didnt find one a month or so ago.

GL with the sale mate, Very cheap!

oil line is a M17 bolt and I made a braided unit.

the stock one will fit BUT you'd have to derestrict the oil line slightly with a .8mm drill bit as this turbo needs more oil than the stock turbo

ok so it comes with a braided oil line and that will fit in a rb20?

i dont no what you mean by drilling a hole? lol

ok so it comes with a braided oil line and that will fit in a rb20?

i dont no what you mean by drilling a hole? lol

no for sale is the turbo only

you'll need to either use your stock oil line, a .8mm drill bit and open up the restrictor before bolting on (search sliding performance high flow turbo pics - http://www.skylinesaustralia.com/forums/Sl...formance+turbo)

or you'll need to purchased a new oil line

my oil line is buggered, trust me you dont want it..... its been bolted on/off/on/off a few times, & being far too tight its cracked. thrown away.

post-18854-1241247638_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...