Jump to content
SAU Community

Pitlane Performance

SLY-L20

By SLY-L20,
in South Australia

 Share

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

kidafa Veteran

kidafa

Posted
Posted

are you guys busy tomorrow? Need some heat applied to a front/dump pipe on the stagea as it lightly taps the floor and bend it a tiny bit... Could all be done on the car its just i dont have enough heat to do it myself :D

SLY-L20 Community Regular

SLY-L20

Posted
  • Author
Posted (edited)

MOVING 30 SECONDS DOWN RD TO NEW SHED!!! RAN OUT OF ROOM ALREADY

NEW ADDRESS IS 2/60 STANBEL RD DIRECTLY ACROSS THE RD FROM PRO FITNESS IN PURPLE BUILDING. WE WILL STILL BE AT U3/26 STANBEL RD TILL SAT AND THEN BY MONDAY WE WILL BE COMPLETELY MOVED IN TO OUR BIGGER AND BETTER ALARMED SHED, U2/60 STANBEL RD

THANKS

Edited by SLY-L20
kidafa Veteran

kidafa

Posted
Posted
we dont currently have oxy to heat it but i can remake that section cheap for you!

It only needs to be bent down like 5mm at the most in one spot dont think it would be worth re-making... what would you do just cut it and weld anothe peice in their at a diff angle or something?

kidafa Veteran

kidafa

Posted
Posted

Its on the under side so it would need to be pulled off.

If unbolted the cat back and pulled the dump down slighlty and it bends it enough to stop it from tapping for a day or so but then it just goes back to its normal position after a day or so... :P

Ideas apart from heating it and bending it? I can get access to an oxy set on sat. which looks like the best thing to do atm but I do however have tomorrow off work and coud take it somewhere.

DSTROY Grand Master

DSTROY

Posted
Posted
Its on the under side so it would need to be pulled off.

If unbolted the cat back and pulled the dump down slighlty and it bends it enough to stop it from tapping for a day or so but then it just goes back to its normal position after a day or so... :ninja:

Ideas apart from heating it and bending it? I can get access to an oxy set on sat. which looks like the best thing to do atm but I do however have tomorrow off work and coud take it somewhere.

Just take it to Exhaust tech or somewhere like that :P

SLY-L20 Community Regular

SLY-L20

Posted
  • Author
Posted

hey guys no offense but this is a thread for our business opening not to discuss where ELSE you can take your car for a quick fix haha

Thanks guys

I am here now if you want me to have a look at it for you! Im sure we can work something out!

Simon

  • 2 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...