Jump to content
SAU Community

Recommended Posts

hey guys

i have tried to search up about this but cant find anything clear on what steps u have to take to get the transfer over from nsw to vic.

im looking at buying a new car but its got nsw plates on it.

i know i have to get a road worthy cert but does vic roads have to inspect the car as well?

if anyone has been through this any help would be much appreciated =]

my main concern isnt getting the road worthy just want to know if vic roads have to check over the ccar

cheers

Link to comment
https://www.sau.com.au/forums/topic/268200-transfering-rego-nsw-vic/
Share on other sites

Hey Tin,

they will look over the car, but solely to check the numbers.

All you need is an appointment, a RWC and a declaration of sale from the previous owner. Make sure that includes his license number, date of birth and current address.

Good luck, bruv!

When I did mine, I let the rego run out in NSW before organising VIC rego, however:

I had a road worthy done on the car by a Vic Roads accredited centre within the 30 day limit. I took the road worthy to the vic roads office and told them it was a new registration, along with the receipt from sale (just a word doc the seller and I signed).

The lady asked how much I wanted to declare the car for even though the receipt told her. I paid my 12 months VIC rego plus stamp duty and the $90 to put my plates back on. Was just over $2K from memory.

To get the remaining rego back from NSW, I believe you need to apply to the RTA up there like you would normally do for Vic Roads down here. You don't transfer as such.

I walked out with a VIC registered car.

HTH :P

**Edit - just saw post above, they don't need to see the car, that can come up if there are any questions over the value but definately don't need to sight it. Sighting the car is more common on first rego, e.g. after compliance.

thanks guys for the help so far.

so really i just need a RWC, make an appointment and pay for new 12months reg, stamp duty is that correct?

cause the thing is the sellers rego runs out in 2 weeks =/

and say if i cant get the rwc in time that would prbly mean vic roads would have to see the car right?

^^

Yes you are correct

If you can't get the RWC in that time, yes potentially they may want to see it as when it is does eventually get a roadworthy, it will be unregistered. I am not 100% sure if when renewing NSW rego, the car needs a pink slip at the same time but possibly get the seller to renew in NSW to buy yourself some more time then just cash the rego in up there when you are ready.

I wouldn't have thought you would struggle to get a RWC inside 2 weeks though down here, waiting lists in my experience aren't that long normally.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...