Jump to content
SAU Community

Recommended Posts

For sale is a:

Nissan Pulsar 1992 N14 SSS (jap spec)

209 000kn (less on the actual motor)

Lowered springs

16: BBS alloys (only 3)

Sony CD player with stacker

6" pioneer speakers

Sports seats

Cat back exhaust

short shifter gear box

New clutch put in not long ago

The car has ran out of rego, needs a new battery, the car also has some minor scratches along the body on the drivers side, dinted rear bumper, needs a replacement drivers side lower control arm and replacement mirror. What you see is what you get.

post-22289-1241420530_thumb.jpg post-22289-1241420557_thumb.jpg post-22289-1241420584_thumb.jpg post-22289-1241420621_thumb.jpg

Selling as is

$2200 ono

Contact 0411268451 or PM me.

Link to comment
https://www.sau.com.au/forums/topic/268364-nissan-pulsar-sss-n14-jap-spec/
Share on other sites

  • 2 weeks later...
  • 2 months later...
thats not a japspec mate its ozzie spec

front bar

wheel archers

rear wing

interior

etc

post-22289-1250749783_thumb.jpg

Its got:

Factory short shifter

Sports seat front/back

Made in Japan plate seen above

Dont know what happened with the rest as we are the second owners in Australia

Tom

Edited by Mid_Nite_R33

is this jap spec or JDM? because i wasn't aware of any sr18 pulsars being sold in australia without being privately imported. and why does the plate say sr18 when there is a 2.0L badge on the side of the car? could be that the plate has been swapped. seems a bit dodgy to me that the plate has the wrong engine size on it. that alone is enough to not have the car able to be registered without needing a blue plate for the engine capacity (unless it is only a sr18 and someone stuck 2.0L badges on it thinking it was).

normally when people say jap spec, it basically means series 2 as the first series of the n14 pulsars made for the australian market were made in australia. then from feb 1993 through 1995 nissan imported the series 2 n14 (as they did with all the n15). and going off all the things i can see in the pic, ul11ke_180 is right, it is a aus spec if it isn't a JDM.

is this jap spec or JDM? because i wasn't aware of any sr18 pulsars being sold in australia without being privately imported. and why does the plate say sr18 when there is a 2.0L badge on the side of the car? could be that the plate has been swapped. seems a bit dodgy to me that the plate has the wrong engine size on it. that alone is enough to not have the car able to be registered without needing a blue plate for the engine capacity (unless it is only a sr18 and someone stuck 2.0L badges on it thinking it was).

normally when people say jap spec, it basically means series 2 as the first series of the n14 pulsars made for the australian market were made in australia. then from feb 1993 through 1995 nissan imported the series 2 n14 (as they did with all the n15). and going off all the things i can see in the pic, ul11ke_180 is right, it is a aus spec if it isn't a JDM.

THERE IS AN SR20DE under the bonnet

Well this car was privately imported and it was an SR18 to begin with, so thats why you're so confused. if you have read the ad properly you'd see that the engine was swapped hence the engine has less km's done than the actual car.

If the car was registered until January 2009 when I simply didn't bother re-newing it why it be a problem to register it again?

The engine is legit.

tom

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
×
×
  • Create New...