Jump to content
SAU Community

Recommended Posts

I was changing my spark plugs last weekend and something strange happened.

As I was putting the new set in I got the the last plug no.6 closest to the firewall. Normally the Plug would rotate 10-11 times before I would need the torque wrench to tighten them up. But No. 6 only went around 4 times! Thinking nothing of this I went to put the coil packs back on only to find that now the no. 6 pack was sitting too high to do up the securing bolts!

So I went in again removed plug six and then had a look down it with a torch...

5-6 threads from the bottom was all this black crap. Probably carbon deposits. It was all jammed up in the thread, this didn't allow the plug to go down properly.

Has anyone got any easy solutions to this problem?

So far I have tried the following...

Cutting down a toothbrush (cleaning it up) and then using some carby cleaner to dissolve the carbon.... didn't work

Getting a cheap bottle brush and then using some carby cleaner to dissolve the carbon.... didn't work

Getting a old sprak plug cutting vertical grooves in it (like a tap/die) to collect the gunk... worked but took 6 hrs!

I would really like to know if anyone out there has a better, cheaper and easy solution than this, so I can clean the threads in the other five cylinders!

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/26856-spark-plug-problem/
Share on other sites

I've found carbon buildup to be really hard to remove. I think for a start a wire brush would be a lot better than a toothbrush, but even then I have worn out more than 2 wire brushes before I was able to clean carbon off something once. I'm not sure what sort of solvent disolves it, but finding the right type would be the first step I think. I know that carbie cleaner doesn't cut it, nor does turps or methelated spirits.

The best place to ask would be your local spare parts shop, they probably have some stuff designed specifically to disolve carbon.

Are you sure you need to clean the other 5 cylinders though? If they all went in all the way they should be fine.

if the thread has carbon and u cant install the plugs all the way in u could use a tap on the thread but u have to make sure u clean all the shavings , dont drop any in the cil .

i never had the prob that bad so i couldnt screw the plugs in .

i had the same problem and got sick of it and though f**K it and ran the tap through and droped shavings down the cyl put everything back on and never had a problem as the shavings are only small and i didnt care as there was gona be a engine transplant going on soon any way but i never had a drama but it could all go wrong to i might have been lucky

If you have really small metal shavings, chances are they will get burnt off when the engine fires.

What you can do if you do drop some small particles in there is put a compressed air line into the hole (not sealing it in) and switch it on. This will pressurise the cylinder with air and hopefully blow out whatever is in there. The same way that you can put a small scrunched up bit of paper into the neck of a bottle on its side and try blowing it out with your mouth. It'll come straight back out rather than blowing into the bottle. Of course, small particles may stick in the oil in the cylinder or fall down onto the rings, so it might not get everything out.

just a thought...

Maybe try cutting the grooves in the spark plug...as mentioned before, to act as a tap. But also break out all the guts of the spark plug aswell (or drill hole through it). This will allow you to feed an airline through the centre of the plug.

Using a box spanner (with the airline passing through it) you should be able to cut away the carbon while pressurising the cylinder at the same time to stop particles from getting in there.

Just a thought, ive never tried it or heard anyone that has.

if u do that how are u going to get the shavings out that will be left stuck on the tread ? if i was going to use a tap i would put a rag inside the the cil and leave the last bit on the botton of the tread , when i finish the job blow compressed air in the hole so shavings will come out then carefully ( using a long nose or simmilar ) pull the rag out and hopefully no shavings drop in the cil .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...