Jump to content
SAU Community

Recommended Posts

Hi all..

I'm after some help in tuning up my RB20det which is sitting in my 260z.. I've got a fully programable EMS computer with a Handset.

The car came with the ems but wasn't running due to some mechanical issues.. All of these issues are now sorted except the EMS. The car seems to be running fine but it doesn't produce ANY power... The turbo spools up and the hand set reads 10psi boost but there is no difference between on boost and off boost.

Was wondering if anyone on here was running an EMS that could give me an idea of the settings that you are using.

The only modification to this one is a larger VG30 Non ball bearing turbo + 2.5" exhaust.

Is it possible to copy maps and settings from one EMS to another?

I'm in Adelaide and any help would be appreciated!.

Trav

Have you got the ems cable to connect the ems to a laptop or pc and the ems software to setup using laptop or pc. If not their url is http://www.fuel-injection.com/. you can download it there.

Which ems have you got mine is the Duel Sport.

Skyrine-Dave,

thanks for that mate that will definatly be of help, what sort of power did you get out of it with those mods? did the EMS make much of a difference for you?

51Jay, the model number is QI-4 from around about 1999 so i'm not sure if that means its a dual sport or not.

Trav

R31-GTSX, thats a dual sport model. I have the QM4/QI4.

With that setup it ran 236hp@wheels. Which really isnt that great considering what is done to it.

When you go into setup it should have a 1, or 2 down the bottom right? i think. That indicates which map you are on. I havent used this before but i think you can have a tune for say outright HP or a tune for economy and switch between the two.

Dave

236hp isn't bad at all!

i'd be pretty happy with that, do you have a fuel pressure regulator on yours? if so what fuel pressure are you running on boost and off boost.?

A couple of other things i have to do first is install a surge tank and some larger diameter fuel lines then i'll hook it up to the lap top and punch in the numbers you gave me... then i'll go from there.. Its a good start!

I'm just not sure how different mine would be running a lower spec fuel pump than yours.. plus the zed's not intercooled as yet.

Thanks again.

Trav

i have another tune sheet i can send ya, but it was tuned for a GTR intercooler, and when i ran my setup on that tune with a stocko 32 cooler the car ran waaay to rich and managed to foul a set of plugs in 2 weeks.

I got the stocko reg on my car, as i have 460cc injectors going in soon. Dont know if i should get a rising rate reg or not.

as for fuel pump. I had the richer map tuned for a R33 GTS-t fuel pump. So whatever pump you have should be fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...