Jump to content
SAU Community

Recommended Posts

Hi Fellas,

I recently conducted my RB30 short block build and I am aiming for 370rwkw. For this reason, I will be selling my Nismo 555cc injectors. They are as new and hold up very well.

At 312 rwkw they were on 80% duty cycle, so they are probably good for around 330 - 340 rwkw.

I am asking for $499.00, as I know they still sell for $849.00 from Slide performance (which is the cheapest I could find them).

They are an excellent upgrade for anyone chasing power up to 330 rwkw.

The only reason I am selling them is because I must upgrade to 740cc injectors.

Cheers.

Hi Fellas,

I recently conducted my RB30 short block build and I am aiming for 370rwkw. For this reason, I will be selling my Nismo 555cc injectors. They are as new and hold up very well.

At 312 rwkw they were on 80% duty cycle, so they are probably good for around 330 - 340 rwkw.

I am asking for $499.00, as I know they still sell for $849.00 from Slide performance (which is the cheapest I could find them).

They are an excellent upgrade for anyone chasing power up to 330 rwkw.

The only reason I am selling them is because I must upgrade to 740cc injectors.

Cheers.

Top feed or Side feed

Are they out of the car yet?

Would like to see a pic just to gauge quality.

Hi mate,

They are still in the car as they are the injectors I am using on my current setup.

I need the funds from these injectors to purchase my 740cc injectors, hence, the reason why I cannot take them out, until sold.

Thanks

Price has gone up to $699.

Sorry fellas, but I just noticed Sliding Performance up'd his prices to $1,279 for the 555 nismo injectors.

I need to sell these injectors to fun my 740 cc injectors, thus, the new price is $699.

I've opened up another thread with the updated price.

Cheers.

And yes they are the yellow top side feed Nismo 555cc injectors. 8 Months old.

Just a heads up- are u going to clean and flow test them? otherwise the next person who buys them will have to, as the fuel can dry up/cause clogs and cause spraying issues for the next car... the best way to avoid that is get them cleaned and then check they are flowing properly....

I'll explain once again...

I originally had them up for $499. AT this time, I was under the impression Sliding Performance was selling them for $859 (As advertised on the web site).

However, when I got in contact with Slide, he said that they were not the updated prices, and that he in fact wanted $1,279 for the injectors.

Since I have to fund the purchase of my 740cc injectors, I had to raise the price of the ones I am selling.

$699 is still a bargain price considering they are worth double that!

Would you flow test them and clean if necessary at that price

To test flow them is $35 each.. That's $210........ So no, I would not as that would mean I would only be getting $440 for them ($650-$210)

Nonetheless, I can post them via express post once taken out, and if you put them in your vehicle within 4-5 days they'll be fine.

Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...