Jump to content
SAU Community

Recommended Posts

Hi Fellas,

I recently conducted my RB30 short block build and I am aiming for 370rwkw. For this reason, I will be selling my Nismo 555cc injectors. They are as new and hold up very well.

At 312 rwkw they were on 80% duty cycle, so they are probably good for around 330 - 340 rwkw.

I am asking for $499.00, as I know they still sell for $849.00 from Slide performance (which is the cheapest I could find them).

They are an excellent upgrade for anyone chasing power up to 330 rwkw.

The only reason I am selling them is because I must upgrade to 740cc injectors.

Cheers.

Hi Fellas,

I recently conducted my RB30 short block build and I am aiming for 370rwkw. For this reason, I will be selling my Nismo 555cc injectors. They are as new and hold up very well.

At 312 rwkw they were on 80% duty cycle, so they are probably good for around 330 - 340 rwkw.

I am asking for $499.00, as I know they still sell for $849.00 from Slide performance (which is the cheapest I could find them).

They are an excellent upgrade for anyone chasing power up to 330 rwkw.

The only reason I am selling them is because I must upgrade to 740cc injectors.

Cheers.

Top feed or Side feed

Are they out of the car yet?

Would like to see a pic just to gauge quality.

Hi mate,

They are still in the car as they are the injectors I am using on my current setup.

I need the funds from these injectors to purchase my 740cc injectors, hence, the reason why I cannot take them out, until sold.

Thanks

Price has gone up to $699.

Sorry fellas, but I just noticed Sliding Performance up'd his prices to $1,279 for the 555 nismo injectors.

I need to sell these injectors to fun my 740 cc injectors, thus, the new price is $699.

I've opened up another thread with the updated price.

Cheers.

And yes they are the yellow top side feed Nismo 555cc injectors. 8 Months old.

Just a heads up- are u going to clean and flow test them? otherwise the next person who buys them will have to, as the fuel can dry up/cause clogs and cause spraying issues for the next car... the best way to avoid that is get them cleaned and then check they are flowing properly....

I'll explain once again...

I originally had them up for $499. AT this time, I was under the impression Sliding Performance was selling them for $859 (As advertised on the web site).

However, when I got in contact with Slide, he said that they were not the updated prices, and that he in fact wanted $1,279 for the injectors.

Since I have to fund the purchase of my 740cc injectors, I had to raise the price of the ones I am selling.

$699 is still a bargain price considering they are worth double that!

Would you flow test them and clean if necessary at that price

To test flow them is $35 each.. That's $210........ So no, I would not as that would mean I would only be getting $440 for them ($650-$210)

Nonetheless, I can post them via express post once taken out, and if you put them in your vehicle within 4-5 days they'll be fine.

Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...