Jump to content
SAU Community

Recommended Posts

THERES IS NO ASKING PRICE FOR THIS IMMACULATE GTR.

WILL SELL TO THE OFFER THAT APPEALS TO ME MOST.

you all know what it is worth so DO NOT put a ridiculously low bid.

Genuine offers only!

car needs to go, owner has other commitments

1993 model r32 gtr, original grey colour in immaculate condition. No scratches or dents. rarely driven. allways serviced with the best oil's and coolant. 150,000 klms and reliable!

P1buddy Club wheels 17x9.5's

DBA 4000 series slotted rotors with green stuff pads

Bilstein coilovers

CUSCO castor adjustables

CUSCO camver adjustables rear

Midori upper adjustable camber arms

APEXI Power FC with hand controller

HKS type-S engine oil cooler

HKS Fuel rail

HKS 900cc injectors

HKS primary exhaust pipes

HKS Cam Gears an Gates Racing belt

Tomei cams

n1 turbo's

Sard Fuel Reg

braided hoses throughout!

Alloy surge tank

Walbro Fuel pump

External Bosch 700hp Fuel pump

Splitfire coils

Brand new crank angle sensor

Brand new ignition module

Brand new ignitor harness

Brand new Z32 airflow meters

Brand new APEXI Super suction kit with Z32 plugs

Custom advan airbox

New N1 water pump,timing belt idler, an adjustment pulley with new half moon cam seals

PWR Radiator

Nismo strut tower Brace-Front

Jun metal Intake gaskets

twin HKS Sequential BOV's (hidden in gaurds)

HKS wastegate

HKS FMIC with HKS hard piping 600x300 by 110

TRUST Clear timing belt cover

5 Puk Jim Berry Clutch(heavy duty single plate)

New nismo slave Cylinder an Pivot ball

Greddy Exhaust temp gauge with memory recall

Greddy Boost gauge with memory recall

Greddy A-Pillar Dual pod gauge holder

Greddy Profec-B eletronic boost control

Greddy turbo timer

latest cobalt series Autometer monster tacho

Blue led dash lights

Sparco Racing - driver side

Sparco steering wheel

i might of left some things out but have reciepts for $$$$$

Car has made 320awkw on 1.1 bar can make more power but this is perfect for street.

it has ran a time of 11.6 at WSID on premium unleaded.

Located in sydney.

I WILL BE PUTTING THIS CAR FOR SALE ON OTHER SITE IN 1 WEEK

so you guys have the first preference now, dont waste it.

post-60376-1242219383_thumb.jpg

post-60376-1242219455_thumb.jpg

post-60376-1242219520_thumb.jpg

post-60376-1242219544_thumb.jpg

post-60376-1242219584_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/269926-immaculate-93-r32-gtr/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...